Search results
1976
Case study
稳定的弹簧测试
定制工程实例我们的客户需要在压缩状态下测试许多小型轻质弹簧。为避免弹簧弯曲和侧向移动，需要支撑主轴或导向杆。 Mecmesin设计并提供了带有导杆的压缩探头，以精确测试被测弹簧的尺寸。与我们的软件控制的MultiTest支架一起使用时，它们可以快速插入弹簧并进行高度可重复的测试。
1978
[Page extract]
ASTM D2105
ASTM D2105 determines the comparative longitudinal tensile properties of fiberglass pipe when tested under defined conditions of pretreatment, temperature, and testing machine speed.
1979
[Page extract]
Why the ring crush test is critical for paperboard strength
Paperboard packaging must combine cost-efficiency with protective performance.
1980
[Page extract]
TAPPI T 402
Standard conditioning and testing atmospheres for paper, board, pulp handsheets, and related products, Test Method TAPPI/ANSI T 402 sp-13
1981
[Page extract]
ISO 2439
The indentation hardness of flexible cellular materials is a measure of their load-bearing properties.
1982
[Page extract]
ASTM D2718
These test methods determine the shear properties of structural panels associated with shear distortion of the planes parallel to the edge planes of the panels. Both shear strength and modulus of rigidity may be determined.
1983
[Page extract]
ANSI/EIA 364-38B
This standard establishes a test method to determine the axial tensile load that can be applied to a mated pair of connectors and the holding effect of a connector cable clamp without causing any detrimental effects upon the cable or connector when subj
1984
[Page extract]
Why torque testing is essential in packaging
Prevents leakage in liquid containers
Ensures seal integrity and prevents contamination
Confirms child-resistant closures are effective and compliant
Improves user experience by avoiding over-tightening
<
1985
[Page extract]
ASTM D1781
This test method covers the determination of the peel resistance of adhesive bonds between: a relatively flexible adherend and a rigid adherend; and the relatively flexible facing of a sandwich structure and its core, when tested under specified conditi
1986
[Page extract]
BS EN 1270
Basketball equipment, Ball-games equipment, Sports equipment, Classification systems, Dimensions, Safety measures, Performance, Properties, Performance testing, Mechanical testing, Sports nets.
1987
[Page extract]
ASTM D1000
These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows:
Class 1—Non-elastomeric backings made from materials
1988
[Page extract]
Common challenges in yield point testing
Specimen alignment issues
Misalignment during clamping can cause uneven stress distribution, resulting in inaccurate readings.
1989
[Page extract]
ASTM D3787
This test method describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation.
1990
[Page extract]
ISO 11608-5
This part of ISO 11608 specifies requirements and test methods for the automated functions of needle-based injection systems with automated functions (NIS-AUTO), for the administration of medicinal products in humans.
1991
[Page extract]
BS EN ISO 80369-1
BS EN ISO 80369 “Small-bore connectors for liquids and gases in healthcare applications. Connectors for intravascular or hypodermic applications”.
This standard replaces BS EN ISO 594-1: 1986, BS EN 20594-1:1994, and BS EN 1707:1997.
1992
[Page extract]
BS EN 565
Mountaineering equipment, Outdoor sports equipment, Sports equipment, Safety measures, Equipment safety, Tape, Webbing, Tensile strength, Stability, Weight measurement, Marking, Test specimens, Testing conditions
1993
[Page extract]
ASTM D622-99
ASTM D622 is a test method intended for use in testing the conventional types of hose employed for the operation of air brake and vacuum brake systems, either on a single motor vehicle or as connecting or transmission lines in a combination of vehicles<
1994
[Page extract]
BS EN 12242
The BS EN 12242 test method is used to determine the peel strength of a touch and close (also known as “hook and loop”) fastener through a 180° peel test that is able to determine average peel and the peel strength characteristics of the product for a g
1995
[Page extract]
ISO 20126
This International Standard specifies requirements and test methods for the physical properties of manual toothbrushes in order to promote the safety of these products for their intended use.It does not apply to manual interdental brushes and powered or
1996
[Page extract]
ASTM D 2979
1.1 This test method covers measurement of the pressure sensitive tack of adhesives.
1997
[Page extract]
ASTM D3354
ASTM D3354 is a test method that provides quantitative information on the degree of blocking i.e. unwanted adhesion between layers of plastic film.
1998
[Page extract]
BS EN 12814-3
BS EN 12814-3 is a tensile creep test method for testing welded joints of thermoplastics semi-finished products.
1999
[Page extract]
BS EN 50289-3-9
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Flexural strength, Bending stress, Bend testing, Stiffness
2000
[Page extract]
ASTM D5587-08
This test method covers the measurement of the tearing strength of textile fabrics by the trapezoid procedure using a recording constant-rate-of-extension-type (CRE) tensile testing machine.