Search results
2276
[Page extract]
ASTM C1576
This standard test method covers the determination of slow crack growth (SCG) parameters of advanced ceramics by using constant stress flexural testing in which time to failure of flexure test specimens is determined in four-point flexure as a function
2277
[Page extract]
ASTM D6746-15
ASTM D6746 is a test standard that covers methods to evaluate a characteristic of raw rubber or unvulcanized rubber compounds that is designated as green strength.
2278
[Page extract]
BS EN ISO 7864
BS EN ISO 7864:2016 specifies requirements for sterile hypodermic needles for single use of designated metric sizes 0,18 mm to 1,2 mm.
2279
[Page extract]
ASTM D5649-01
This test method is used to make comparative assessments of the securing or locking effect of adhesives used in threaded assemblies.
2280
[Page extract]
BS EN 1465
Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.
2281
[Page extract]
ASTM D1600
ASTM D1600 is a source of reference for definitions of abbreviated technical terms used in the plastics industry
Standards can be obtained from appropriate standard authorities.
2282
[Page extract]
BS EN 2591-412
Covers a method of assessing the insertion/extraction forces for contacts used in elements of connection.
2283
[Page extract]
BS ISO 5893
ISO 5893 specifies requirements for tensile-testing systems operating at constant rate of traverse and suitable for testing rubbers, plastics and adhesives, although any one system may only be applicable to a narrower range of materials.
2284
[Page extract]
TAPPI T 541
This method describes a procedure for measuring the internal fiber bond strength (z-direction tensile strength) of paperboard using an instrument that subjects a normal separation force to 6.45-cm2 (1-in2) specimen.
2285
[Page extract]
BS EN 1125
Ironmongery (buildings), Panic bolts, Bolts (security), Emergency exits, Doors, Fire doors, Safety devices, Closing and check mechanisms, Fire safety in buildings, Means of escape from fire in buildings, Hazard prevention in buildings, Buildings open to
2286
[Page extract]
BS EN ISO 10619-1
BS EN ISO 10619-1 is a test method covering bending tests on rubber or plastics hoses and tubing.
2287
[Page extract]
BS EN 12562
Synthetic fibres, Polyamide fibres, Aramide fibres, Textile products, Textile testing, Yarn, Filament yarns, Filaments, Filament (textile fibre), Yarn testing, Yarn linear density determination, Elongation at fracture, Elongation, Force measurement, Mec
2288
[Page extract]
BS EN 681-1
This standard specifies requirements for materials used in vulcanized rubber seals for:
1) cold potable water supply (up to 50®C);
2289
[Page extract]
ASTM D1566
ASTM D1566 is a source of reference for definitions of technical terms used in the rubber industry
Standards can be obtained from appropriate standard authorities.
2290
[Page extract]
BS EN ISO 10319
Geosynthetic materials, Geotextiles, Textile testing, Cloth, Textile products, Fabric testing, Breaking load, Tensile testing, Test specimens, Width, Dimensions, Specimen preparation, Testing conditions, Test equipment, Wet-strength tests
2291
[Page extract]
BS EN 2591-408
Gives a procedure for measuring the mating and unmating forces for elements of connection.
2292
[Page extract]
ISO 4587
Specifies a method for determining the tensile lap-shear strength of rigid-to-rigid bonded assemblies using a standard specimen under specified conditions of preparation and testing. This test procedure does not provide design information.
2293
[Page extract]
ISO 7439
ISO 7439:2002 is applicable to single-use copper-bearing intra-uterine contraceptive devices and their insertion instruments.
2294
[Page extract]
ASTM C1469
This test method covers the determination of shear strength of joints in advanced ceramics at ambient temperature.
2295
[Page extract]
CETIE Guide 5
This document gives background information and recommended best practices for the application of plastic flat-top screw-on caps onto PET bottles for beverages. It covers all closure sizes and beverage product types.
2296
[Page extract]
BS 373
Wood, Mechanical testing, Strength of materials, Test specimens, Specimen preparation, Moisture measurement, Density measurement, Physical property measurement, Static loading, Impact testing, Bend testing, Compression testing, Shear testing, Cleavage,
2297
[Page extract]
BS 8888
BS 8888:2013 is the newly amended up to date technical product specification (TPS) that brings together, in one easy-to-follow document, all international standards needed to prepare technical product specifications (TPS), in accordance with geometrical
2298
[Page extract]
BS EN 14704-1
Methods for testing using stripsof fabric in straight strip form or loops, which can be used to measure elasticity and related properties of fabrics, excluding narrow fabrics.
2299
[Page extract]
BS EN ISO 13127
This standard is only to verify that panel-tested closures with minor modifications are still compliant, by applying mechanical tests as more economical than further full panel tests with children and with adults.
2300
[Page extract]
ASTM D6797-07
This test method describes the measurement for bursting strength of woven and knitted textiles taken from rolls of fabric or fabric taken from garments.