Search results
976
[Page extract]
Standards and compliance in shear testing
Adhering to recognised standards ensures consistency and comparability of results. Common examples include:
977
[Page extract]
Standards and procedures
FCT results must be consistent and comparable, which is why the test is carried out to recognised standards:
978
Sensor
Sensors - MultiTest-dV
Force sensors
The MultiTest-dV is a highly flexible tester, which can be configured with either a Touchscreen or Advanced Force Gauge for product testing or an Enhanced Load Sensor for basic materials testing.
AFGA digital force gauge with advanced…
979
[Page extract]
Power and flexibility for your materials testing
Start measuring stress/strain, tensile, shear, flexure and compressive forces to evaluate your materials. It takes just a few minutes to create your own step-by-step test routines.
980
[Page extract]
Introduction to ergonomic strength testing
Ergonomic strength testing is a structured method for measuring an individual's capacity to perform physical tasks safely and efficiently.
981
[Page extract]
Introduction to five-point bend testing
The five-point bend test is a specialised method for assessing the mechanical performance of structural panels, particularly their resistance to planar shear forces.
982
[Page extract]
Electronic components and assemblies
Electrical assemblies rely on a collection of electrical components that have been connected together on a PCB or other surface to perform a specific function.
983
[Page extract]
Why is ultimate compressive strength important?
Ultimate compressive strength is a critical parameter in engineering design, safety, and product validation.
984
[Page extract]
How is the trapezoidal tear test performed?
A standard trapezoidal tear test follows a consistent sequence:
985
[Page extract]
How to conduct a Concora crush test
Step-by-step procedure
Specimen preparation - Cut medium to the required size, typically 152.4 mm by 25.4 mm strips, ensuring clean edges.
986
[Page extract]
How is the 135° peel test performed?
Specimen preparation
Test specimens are usually strips cut from the sealed edge of a tray or container.
987
[Page extract]
The 3-Point Bend test goes to Summer School
Both Dr. Cote and Grubbs agree that one of the highlights of their year is the Materials Science summer course for high school students, where they had students design their own candy composites.
988
[Page extract]
What is torque testing?
Torque testing measures the rotational force required to turn or twist an object. In packaging, it is most often applied to closures such as caps, lids and twist-top mechanisms to ensure they open and close within defined performance limits.
989
[Page extract]
What is a three-point bend test?
A three-point bend test is a widely used method for determining the flexural properties of materials. It involves applying a load at the midpoint of a specimen supported at two points, creating a bending force.
990
[Page extract]
Best practices for reliable torque testing
Accurate and repeatable torque testing depends on attention to several technical factors.
991
[Page extract]
What is Young’s modulus?
Young’s modulus - also known as the modulus of elasticity or elastic modulus - defines how stiff a material is when a force is applied.
992
[Page extract]
Introduction to tear testing
Tear testing is a quality control procedure used to measure the resistance of a material to tearing under controlled conditions.
993
[Page extract]
How the strip method works
The strip method involves cutting a specimen to a precise width, typically 50 mm or 25 mm depending on the applicable standard, and mounting it in the grips of a tensile testing
994
[Page extract]
Why choose Mecmesin for flexural testing
Mecmesin’s flexural test systems are engineered for precision, repeatability, and compliance with international standards.
995
[Page extract]
How running torque is measured
Running torque is typically measured using precision torque sensors mounted within a controlled test stand. The component under test is rotated at a defined speed, and torque is measured continuously during motion.
996
[Page extract]
Introduction to tangent modulus
In materials science and engineering, understanding how materials respond to stress is essential for ensuring safety, performance, and longevity. One key parameter used to characterise this behaviour is the tangent modulus.
997
[Page extract]
What is cantilever bend testing?
Definition and purpose
Cantilever bend testing assesses a component’s flexural response by applying a controlled force at a set distance from a fixed end.
998
[Page extract]
Introduction to compressive modulus
Compressive modulus, also known as the modulus of elasticity in compression, is a key mechanical property describing a material’s ability to resist deformation under compressive load.
999
[Page extract]
Applications of running torque testing
Running torque testing is used across a wide range of industries and products, including:
1000
[Page extract]
Speak to an Expert
The Concora Crush Test, as defined in TAPPI T 824, is a critical step in corrugated medium evaluation.