Search results
2451
[Page extract]
Speak to an expert
Discuss your requirements with a Mecmesin specialist to identify the right tension testing solution for your product and process.
2452
[Page extract]
Speak to an expert
Speak to an expert at Mecmesin about your tear resistance testing requirements, from selecting the correct wing tear method to configuring equipment for
2453
[Page extract]
Best practice and future trends
Maintaining accuracy
Calibrate to ISO 6789 or Mecmesin protocols
Use in controlled environments
Validate with certified torque standards
2454
[Page extract]
Significance of connector extraction resistance
Extraction resistance is the connector’s ability to maintain a secure fit during use while still allowing disconnection when necessary. This is especially important where connectors are repeatedly mated and unmated, such as:
2455
[Page extract]
Brushes
Brushes use synthetic or natural filaments to create bristles which are typically clamped to a handle via a ferrule.
2456
[Page extract]
Speak to an Expert
For specialist advice on four-point bend testing—including test setup, standard compliance, and equipment selection—contact Mecmesin’s technical support team.
2457
[Page extract]
Accuracy and repeatability
Achieve a level of accuracy and repeatability that cannot be achieved by manual testers. Reduce your testing time and increase your throughput when performing batch tests.
2458
Case study
ISBT运动帽旋转测试
需求 国际饮料技术专家协会（ISBT）针对软饮料和饮料的技术和科学方面发布了自愿性行为准则。 他们的包装指南包括运动密封件：自愿性标准性能规格和测试方法；指出了用于矿泉水和运动饮料瓶盖的独特推/拉或旋开式嘴盖设计的测试程序。
2459
[Page extract]
ASTM D2653
ASTM D2653 determines the tensile properties of elastomeric yarns made from natural rubber, spandex or other elastomers.
2460
[Page extract]
ASTM D3807
ASTM D3807 is a test method used to determine the strength properties of adhesives in cleavage peel by tension loading. It allows the comparative testing of cleavage/peel strengths of bonded engineering thermoplastic adherends.
2461
[Page extract]
ISO 9047
This International Standard specifies a method for the determination of the adhesion/cohesion properties of sealants with predominantly elastic behaviour which are used in joints in building construction.
2462
[Page extract]
ASTM D6713-14
Materials shall be tested and the individual grades shall conform to specified values of the physical properties such as tensile strength, tensile elongation, tensile modulus, dimensional stability, flexural modulus, and Izod impact; and dimensional pro
2463
Event
Makers Hackathon, June 16-18th 2022, Malmö, Sweden
Who should attend?
Quality Managers, design/product engineers and materials specialist.
What is the exhibition about?
2464
[Page extract]
BS EN ISO 23907
Test methods for various aspects of sharps bin safety requirements. Relevant to us are Penetration test and possibly Handle strength
2465
[Page extract]
NF S86-604
This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.
2466
[Page extract]
ASTM D6117-18
ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:
2467
[Page extract]
NF G30-102
La présente partie a pour objet de décrire une méthode de mesure directe de la pression de contention des garnitures élastiques telles que les bords-côtes de chaussettes, ceinturesde slips et de culottes, gaines et bas dits de confort, et plus généralem
2468
[Page extract]
ASTM D2718
These test methods determine the shear properties of structural panels associated with shear distortion of the planes parallel to the edge planes of the panels. Both shear strength and modulus of rigidity may be determined.
2469
[Page extract]
BS EN 50289-3-16
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Tensile testing, Tensile strength, Performance testing
2470
[Page extract]
ASTM F607-03
The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.
2471
[Page extract]
BS EN 1465
Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.
2472
Event
Tensile Testing: Basics, Tips, & Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
2473
[Page extract]
DIN 6094
Dimensions and specifications for a series of bottle finishes, including corks, crown, screw threads, including bottles with internal pressure.
2474
Event
Materials Testing: Theory and Practice Pt. 1 & 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.