Search results
2176
[Page extract]
ISO 34-2
ISO 34-2 specifies a method for the determination of the tear strength of small test pieces (Delft test pieces) of vulcanized or thermoplastic rubber.
2177
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
2178
[Page extract]
ISO 9856
ISO 9856 specifies a method for determining the elastic and permanent elongation of a conveyor belt and the calculation of the elastic modulus.
2179
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
2180
[Page extract]
BS EN 12814-7
BS EN 12814-7 is a tensile test method with waisted test specimens for testing welded joints of thermoplastics semi-finished products.
2181
[Page extract]
BS EN ISO 8339
This International Standard specifies a method for the determination of the tensile properties of sealants used in joints in building construction.
2182
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
2183
[Page extract]
BS ISO 2285
BS ISO 2285 is a test method for determining the tension set under constant elongation of vulcanised rubber or thermoplastic.
2184
[Page extract]
Standards for yield point testing
Yield point testing protocols are defined by recognised international standards, including:
2185
[Page extract]
USP <381>
This chapter applies to closures used for long-term storage of preparations defined in the general test chapter Packaging and Storage Requirements á659ñ, Injection Packaging.
2186
[Page extract]
BS EN ISO 13127
This standard is only to verify that panel-tested closures with minor modifications are still compliant, by applying mechanical tests as more economical than further full panel tests with children and with adults.
2187
[Page extract]
ASTM C1469
This test method covers the determination of shear strength of joints in advanced ceramics at ambient temperature.
2188
[Page extract]
ASTM D3165
This test method is useful in that the joint configuration closely simulates the actual joint configuration of many bonded assemblies.
2189
Event
Fundamentals of Food Texture Testing
Texture cannot be controlled unless it is measured in a consistent and repeatable manner.
2190
[Page extract]
MIL AS23190A
AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment
2191
[Page extract]
ASTM D1938
ASTM D1938 covers the determination of the force necessary to propagate a tear in plastic film and thin sheeting by a single-tear method. It rates the tear-propagation resistance of various plastic films and thin sheeting of comparable thickness.
2192
[Page extract]
ASTM F2592
1.1 This test method covers the measurement of force displacement characteristics of a membrane switch.
2193
Case study
Wall-mounted air freshener destructive loading evaluation
Requirement
The customer wished to apply a controlled load of 350N to a wall mounted air freshener, replicating the effect of a child standing on it. The load needed to be applied in turn to 4 different planes on the product, e.g.
2194
[Page extract]
ASTM D937-97
1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency.
2195
[Page extract]
ISO 11502
Describes a qualitative and a quantitative method for assessing the tendency of flexible plastics films and sheets to adhere to one another when left in contact for some time, at a specified temperature and under light pressure.
2196
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells
2197
[Page extract]
SAE J 1523
This SAE Recommended Practice defines a procedure for determining shear strengths of adhesives used for bonding automotive oil metal substrates.
2198
[Page extract]
TAPPI T 804
This method is used for measuring the ability of corrugated or solid fiber shipping containers to resist external compressive forces.
2199
[Page extract]
ISO 814
ISO 814 specifies a method for determining the adhesion strength of rubber-to-metal bonds where the rubber part is assembled between two parallel metal plates, using the adhesive system under investigation
2200
[Page extract]
ASTM D2527
ASTM D2527 covers the strength and appearance of the splice in vulcanized rubber-seal material of any size, type, or cross-sectional shape.