Search results
1376
[Page extract]
ISO 9187-2
ISO 9187-2:2010 specifies materials, dimensions and requirements for forms of one-point-cut (OPC) ampoules (forms B, C and D) for injectables.
Ampoules complying with ISO 9187-2:2010 are intended for single use only.
1377
[Page extract]
SAE USCAR-21-4
This specification defines test methods and requirements for validation of solderless crimped connections.
1378
Event
WestPack Trade Show
Lansmont - together with our sister brand Mecmesin - will be participating in the upcoming WestPack trade show!
1379
[Page extract]
ASTM D885/D885M-10a
These [comprehensive] test methods cover the testing of industrial filament yarns made wholly of manufactured organic-base fibers, cords twisted from such yarns, fabrics woven from such cords, and products that are made specifically for use in the manuf
1380
Event
Needle Sharpness & Puncture Resistance Testing
Hypodermic needles are tested to determine how their design influences the ease of insertion into the skin in order to prevent patient pain and skin trauma.
1381
Event
Fundamentals of Compression Testing
How much force is required to register a command when you click your computer mouse?
How much force can a water bottle take before it collapses in its case under a stack?
1382
[Page extract]
BS EN 12453
BS EN 12453:2001 specifies the performance requirements with regard to the safety in use for any type of power operated doors, gates and barriers intended for installation in areas in the reach of persons, and for which the main intended uses are giving
1383
[Page extract]
BS EN ISO 9626
This International Standard specifies the dimensions, surface and mechanical properties of normal- and thin-walled tubing of designated metric sizes 3,4 mm to 0,3 mm, and of extra-thin-walled tubing of designated metric sizes 2,1 mm to 0,6 mm.
1384
[Page extract]
SAE J174M
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters.
1385
[Page extract]
ISO 6922
Specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method is applicable to all types of adhesives.
1386
[Page extract]
ASTM D6109-19
ASTM D 6109 determines the flexural properties for any solid or hollow manufactured plastic lumber product of square, rectangular, round, or other geometric cross section that shows viscoelastic behavior.
1387
[Page extract]
ASTM D4649-03
This guide covers recommended guidelines and test methods for the selection, specification, and use of stretch wrap films for unitizing, reinforcing, and palletizing for indoor environments.
1389
[Page extract]
SAE J174
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 1/4 through 1 in nomial diameters.
1390
[Page extract]
ISO 7886-4
This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design
1391
[Page extract]
ASTM D5635-11
An important factor affecting the performance of membrane roofing systems is their ability to resist dynamic puncture loads. This test method provides a means to assess dynamic puncture resistance.
1392
[Page extract]
ASTM D4255 / D4255M-15a
ASTM D4255 is a test method for testing the in-plane shear properties of high-modulus fiber-reinforced composite materials. The method is divided into two procedures. Procedure A tests laminates clamped between two pairs of loading rails.
1393
Event
Fundamentals of Compression Testing
How much force is required to register a command when you click your computer mouse?
How much force can a water bottle take before it collapses in its case under a stack?
1394
[Page extract]
ASTM D695-15
ASTM D695 is a test method used to determine the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading.
1395
Event
Fundamentals of Compression Testing
How much force is required to register a command when you click your computer mouse?
How much force can a water bottle take before it collapses in its case under a stack?
1396
[Page extract]
SAE J1701M
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user.
1397
[Page extract]
ASTM D3846
ASTM D3486 is a test method used for evaluating the in-plane strength of reinforced thermosetting plastics in flat sheet form in thicknesses ranging from 2.54 to 6.60 mm.
1398
[Page extract]
BS EN ISO 527-2
ISO 527-2 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527-1.
1399
[Page extract]
ASTM D3469
These test methods measure the downward forces during the disengagement of lug-style caps from their respective containers. The methods measure the maximum torque developed while the cap is further disengaged by turning of the container.