Search results
2626
[Page extract]
TAPPI related
TAPPI Standards compared to Related Standards of ISO and ASTM (revised August 2011)
2627
[Page extract]
ASTM C480
This test method covers the determination of the creep characteristics and creep rate of flat sandwich constructions loaded in flexure, at any desired temperature.
2628
[Page extract]
ISO 2493-1
Specifies procedures, based on the two-point loading principle, for determining the bending resistance of paper and board.
2629
[Page extract]
TAPPI T 816
administratively withdrawn 'for lack of timely review'
ASTM D4521 equivalent, withdrawn
2630
Test Frame
Vortex-dv test frame
Vortex test frame
A sturdy twin-column test frame capable of applying torque up to 10 N.m (90 lbf.in). Tall and wide enough to accept a variety of test specimens yet compact to use as a bench-top tester.
View test frame
2631
[Page extract]
Probes
Probes are designed primarily for penetration and puncture resistance testing. There are a variety of tip profiles and sizes available (e.g. cone, chisel, radiused) to simulate the real-world conditions under which a specimen may be compressed.
2632
Event
Materials Testing: Theory and Practice Pt. 1 & 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
2633
[Page extract]
BS EN ISO 6892-1
This part of ISO 6892 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.
2634
[Page extract]
ASTM E8/E8M-13a
These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area.
2635
[Page extract]
BS EN 319
EN319 specifies a method for determining the resistance to tension perpendicular to the plane of the board (“internal bond”) of particleboards, fibreboards, and cement-bonded particleboards.
2636
[Page extract]
TAPPI T 549
This method describes a horizontal plane procedure for the determination of the coefficient of static and kinetic friction of paper measured when sliding against itself.
2638
[Page extract]
BS EN 1799
Applicable to both vertical and horizontal surfaces. To be read in conjunction with BS EN 1504-1:2005
Concretes, Structures, Adhesives, Surfaces, Repair, Performance testing, Physical testing, Flow, Specimen preparation, Test equipment
2639
[Page extract]
CETIE Guide 18
This document provides a collection of test methods for the qualification of plastic flat-top closures applied on PET bottles that are used in the beverage industry.
2640
[Page extract]
ASTM C158
These test methods cover the determination of the modulus of rupture in bending of glass and glass-ceramics. These test methods are applicable to annealed and prestressed glasses and glass-ceramics available in varied forms.
2641
[Page extract]
BS EN 843-1
EN843-1 describes methods for determining the nominal flexural strength of advanced monolithic technical ceramic materials at ambient temperature.
2642
[Page extract]
BS EN ISO 3376
This International Standard specifies a method for determining the tensile strength , elongation at a specified load and elongation at break. It is applicable to all types of leather
2643
[Page extract]
ASTM D1414
ASTM D1414 is used to measure the mechanical properties of vulcanized rubber o-rings. Mecmesin test equipment is relevant to the tensile testing part of this standard, which covers a variety of different tests.
2644
[Page extract]
AEC Q200-005
This specification establishes the procedure and criteria to determine the ability of surface
mounted device terminations and seals to withstand bending, flexing and pulling forces which
2645
Case study
土工水泥基复合材料的抗弯强度
要求Concrete Canvas Ltd.在其ConcreteCanvas®GCCM产品中采用了突破性的材料技术，该产品基本上是混凝土在卷材上的。这种独特的发展通过将织物和混凝土结合起来灵活，易于操作直到水合，赢得了许多创新和卓越设计奖，此后硬化形成了一层耐久的耐火层。
2646
Case study
ISBT运动封口张力测试
要求国际饮料技术专家协会（ISBT）针对软饮料和饮料的技术和科学方面发布了自愿性行为准则。他们的包装准则包括运动密封件：自愿性标准性能规格和测试方法；指出了用于矿泉水和运动饮料瓶盖的独特推/拉或旋开式嘴盖设计的测试程序。两项测试均施加拉伸载荷以评估密封件的质量和完整性：第2.1节-咬合测试和第2.3节-拉伸测试。张力测试的目的是测量喷嘴和底座组件的强度，如果喷嘴太容易断裂，则可能会造成窒息危险。
2647
[Page extract]
Paper & Board
Paper and board are used in a wide range of applications and, as such, they undergo various stages of processing which place significant demands on their material strength.
2648
Software
TestWise Touch™
TestWise Touch™
Our designers work closely with our customers and our textile technologists in a working laboratory to produce an intuitive touchscreen interface to make the Martindale easy to control.
The familiar feel of a touchscreen similar to devices…
2649
[Page extract]
Customised testing equipment and fixtures
Mecmesin testing systems are highly versatile and we specialise in conquering force and torque testing challenges of all sizes.
2650
Case study
鲁尔接头和小孔接头扭矩测试
需求与医疗保健应用中的液体和气体小口径连接器有关的国际标准着重于它们的易用性以及对泄漏或误操作的抵抗力。当前的ISO 80369标准涵盖了一组测试方法，这些方法提供了广泛的功能检查矩阵，推荐用于此类组件的质量保证。 Mecmesin扭矩和力测试系统可帮助您根据这些ISO方法准备用于性能测试的连接器。 小口径连接器用于与患者一起使用的医疗设备或附件，并在麻醉，神经放射，肿瘤，血液学和放射学以及体外诊断实验室和药房活动等医疗保健应用中输送液体或气体。