Search results
1376
[Page extract]
BS ISO 7743
ISO 7743 specifies methods for the determination of the compression stress-strain properties of vulcanized or thermoplastic rubber using a standard test piece, a product or a part of a product.
Four procedures are given:
1377
Case study
Insulation film stiffness testing
Customised engineering example
Familiar with three-point bending to test flexural strength properties?
1378
[Page extract]
What is Ultimate Tensile Strength in Materials Testing?
Ultimate tensile strength (UTS) refers to the maximum stress a material can endure while being stretched before it fails.
1379
Case study
Electrical assembly component strength
Customised engineering example
Due to the complex, asymmetric shapes of electrical assemblies, it can be difficult to grip the soldered, fused and welded parts in a way that mimic the forces applied when in use.
1380
[Page extract]
Introduction to yield point testing
Yield point testing is essential for understanding the mechanical behaviour of materials.
1381
[Page extract]
ISO 594-1
Specification of the requirements for conical (Luer) fittings for use with hyperdemic syringes and needles and with certain other apparatus for medical use such as transfusion and infusion sets.
1382
[Page extract]
ASTM F3014-14
1.1 This test method describes the procedure for penetration testing sharp and blunt needles used for the placement of surgical sutures. It only describes the test procedures (Phase 1) and does not define a test medium at this time.
1383
[Page extract]
ASTM D3578
Scope... 1.1 This specification describes certain requirements for natural rubber gloves used in conducting medical examinations and diagnostic and therapeutic procedures. It also covers natural rubber gloves used in handling contaminated medical
1384
[Page extract]
Introduction to friction in material science
Friction is a critical factor in how materials behave under movement. It is the resistive force that occurs when two surfaces are in contact and attempt to slide against each other.
1385
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
1386
[Page extract]
Introduction to the ring crush test
The ring crush test (RCT) is a key method for determining the edgewise compression strength of paper and paperboard.
1387
[Page extract]
ASTM D3165
This test method is useful in that the joint configuration closely simulates the actual joint configuration of many bonded assemblies.
1388
[Page extract]
*corp ITF TB 03/01
The official Rules of Tennis requires that any ball which is to be considered for use in any tournament which is played according to the Rules of Tennis, shall be named on the official list of balls which have been tested and approved as conforming to t
1389
[Page extract]
Introduction to single lap shear testing
Single lap shear testing is a widely used method for determining the shear strength of an adhesive bond between two overlapping materials.
1390
[Page extract]
ASTM D2061
No one test determines the suitability of a zipper for a specific end use. Since the tests are inter-related more than one may be needed for a complete evaluation.
1391
[Page extract]
Speak to an Expert
Compressive shear testing is essential for verifying adhesive bond strength, layered composite integrity, and internal shear resistance in structural materials.
1392
[Page extract]
Mecmesin solutions for Concora crush testing
Mecmesin offers advanced motorised test stands and fixtures for performing CCT in compliance with
1393
[Page extract]
Performing the flat crush test
A standard flat crush test includes the following stages:
1394
Event
Medical Devices: General testing with 21 CFR Part 11 compliance
Reliable results, trusted compliance: 21 CFR Part 11's role in securing medical device quality testing.
Quality testing of Medical Devices ranges from syringe actuation (break loose and glide), needle sharpness and adhesion strength to Child R
1395
[Page extract]
Introduction to single rip trouser tear testing
Single rip trouser tear testing is a method used to measure a material’s ability to resist the propagation of a tear once it has started.
1396
[Page extract]
How to conduct a floating roller peel test
Carrying out this test requires attention to detail and strict adherence to the procedure. Key steps include:
1397
[Page extract]
Introduction to running torque
Running torque testing measures the torque required to keep a component rotating once movement has started.
1398
[Page extract]
Speak to an expert
Mecmesin offers a complete range of high-precision torque testing instruments designed for packaging, medical, and industrial applications.
1399
[Page extract]
ISO 36
ISO 36 determines the strength required to separate two plies of fabric bonded together with rubber, or a rubber and a fabric ply bonded together. This test is referred to as a “T-peel” test, because as the two adherends are pulled apart, they form the
1400
[Page extract]
Equipment for burst testing
The right equipment depends on the container type, material, and applicable standard.