Search results
951
[Page extract]
BS EN 2747
BS EN 2747 is a tensile test method for testing carbon fibre reinforced plastics.
Before conducting BS EN 2747, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.
952
[Page extract]
ISO 20126
This International Standard specifies requirements and test methods for the physical properties of manual toothbrushes in order to promote the safety of these products for their intended use.It does not apply to manual interdental brushes and powered or
953
Case study
Peel test of semi-rigid packaging for medical device
Customised engineering example
Our client needed to test the peeling quality of a Tyvek® paper lid used to seal a sterile, semi-rigid thermoformed plastic tray containing pre-filled syringes.
954
[Page extract]
BS EN ISO 21181
BS EN ISO 21181 is a test method for determining the relaxed elastic modulus of light conveyor belts.
955
[Page extract]
BS EN ISO 71-2
BS EN 71-2 covers the flammable materials which are prohibited in all toys and the requirements concerning flammability of certain toys when exposed to fire.
956
[Page extract]
SAE USCAR-38
This specification defines basic test methods and requirements for ultrasonically welded cable termination type connections.
957
[Page extract]
ASTM F543-13
This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.
958
[Page extract]
ASTM D5083-17
ASTM D5083 is a test method for measuring the force required to break a reinforced thermoset plastic specimen and the extent to which the specimen stretches or elongates to that breaking point.
959
[Page extract]
ASTM D3914
ASTM D3914 is a test method used to measure the in-plane shear strength of pultruded, glass-fiber reinforced, thermosetting plastic rod in diameters ranging from 19 to 32 mm.
960
[Page extract]
ASTM D6264 /D6264M-17
In ASTM D6264 a quasi-static indentation (QSI) test method is used to obtain quantitative measurements of the damage resistance of a continuous-fibre-reinforced composite material to a concentrated indentation force
961
[Page extract]
BS EN ISO 9000
ISO 9000 gives an overview of the fundamentals and concepts around quality management.
962
[Page extract]
ASTM D926-17
ASTM D926 is a test method that covers the determination of plasticity and recovery of unvulcanized rubber by means of the parallel plate plastometer. Uncompounded, compounded, and reclaim rubber may be tested.
963
[Page extract]
ASTM D3575
ASTM D3575 covers a number of tests for determining properties of polyethylene foams including compressive strength.
964
[Page extract]
ASTM D4482-11
ASTM D4482 is a test method used to determine the fatigue life of rubber compounds undergoing a tensile-strain cycle. During part of the cycle, the strain is relaxed to a zero value.
965
[Page extract]
ASTM D1184
This test method covers the determination of the comparative properties of either metal or wood adhesive bonded assemblies when subjected to flexural stresses with standard shape specimens and under defined conditions of pretreatment, temperature, relat
966
[Page extract]
ASTM D622-99
ASTM D622 is a test method intended for use in testing the conventional types of hose employed for the operation of air brake and vacuum brake systems, either on a single motor vehicle or as connecting or transmission lines in a combination of vehicles<
967
[Page extract]
ASTM D624-00
This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.
968
[Page extract]
ASTM D3810
This test method covers the determination of or the recommendation for minimum application torque that results in a fully degraded removal torque that is at a level greater than the maximum expected reverse-ratchet torque for a Type IA child-resistant c
969
[Page extract]
ISO 11897
ISO 11897 specifies a method for the determination, under given conditions, of the resistance to tear propagation on an edge fold of sacks made from thermoplastic flexible film.
970
[Page extract]
ASTM D1623
ASTM D1623 determines the tensile and tensile adhesion properties of rigid cellular plastics materials and foam. These are often used as insulation and structural materials in the aerospace, automotive and construction industries.
971
Case study
Electrical harness terminal testing
Requirement
Cyprium Motorsports based in Diss, UK, design and produce customised wiring harness systems for sports cars, including Formula 1, Le Mans Prototype, Grand Touring and rally cars.
972
[Page extract]
Standards for texture compression testing
ISO 16305 - Butter firmness
Specifies a method for determining butter firmness under controlled conditions.
973
[Page extract]
ISO 8094
ISO 8094 specifies a test method for determining the adhesion strength of the cover to the core layer. It applies exclusively to steel cord conveyor belts.
974
[Page extract]
ASTM D1871
This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.
975
Case study
Aluminium tube seals pierce compression effort
Requirement
One of the largest packaging tube suppliers in Central Europe specialises in laminated plastic and aluminium tube containers for the cosmetics industry.