Search results
1501
[Page extract]
ASTM D3916
ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.
1502
[Page extract]
CETIE Guide 4
This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.
1503
Case study
Seat belt locking device test
Requirement
The customer requested a system to measure the force required to release the locking mechanism of a car seat-belt whilst it is under tension.
1504
Case study
Sörf tahtası köpük üç noktalı bükülme testi
gereklilik Sert poliüretan (PU) köpükten yapılmış sörf tahtası boşlukları üreten bir şirket, köpüğün sertliğini ve son sörf tahtası ürününün mukavemetini garanti etmek için sıkı bir test programı yürütmektedir.
1505
[Page extract]
BS EN ISO 8295
ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr
1506
[Page extract]
ASTM D76-99
This specification covers operating characteristics of tensile testing machines for the determination of the force-elongation properties of textile materials.
1507
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
1508
Case study
Spor ayakkabı cleats serbest tork
gereklilik Önde gelen bir golf ayakkabısı tedarikçisinin, spor ayakkabı serisindeki değiştirilebilir kelepçelerin salınım torkunu ölçmesi gerekiyordu.
1509
Case study
Uygun maliyetli kablo gücü testi
Özel mühendislik örneği Önemli bir kablo demeti ve konnektör üreticisi, doğrudan bağlanmış bağlantılara sahip farklı çaplara sahip test kablolarını çekme kuvveti için uygun maliyetli bir çözüm için bize yaklaştı.
1510
[Page extract]
ASTM d6108-19
ASTM D6108 covers the determination of the mechanical properties of plastic lumber and shapes, when the entire cross-section is loaded in compression at relatively low uniform rates of straining or loading.
1511
Event
Automotive Component Torque Testing
This webinar will focus on the measurement of the torque resistance in knobs, switches, and torsion springs, which are among several components in automobiles that require testing to ensure quality, performance, and safety.
1512
Case study
Metal bottle cap on glass pull-off test
Customised engineering example
Gripping the base of a glass bottle for a tensile test can be challenging due to the slippy surface and contoured shape.
1513
[Page extract]
ASTM D2344 / D2344M
ASTM D2344 is a test method, which determines the short-beam strength of high-modulus fiber-reinforced composite materials. It is applicable to all types of parallel fiber reinforced plastics and composites.
1514
[Page extract]
ASTM E1820-18ae1
The ASTM E1820 test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness can be measured in the R-curve format or as a point value.
1515
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
1516
[Page extract]
ASTM D378
The ASTM D378 test method is used for evaluating the physical properties of flat conveyor belting, which are used in many industrial applications in which they are subjected to a great variety of stresses and conditions.
1517
Event
Advanced Engineering 2021 - We would love to see you there!
Who should attend?
Engineering professionals and managers from advanced manufacturing sectors interested in quality assurance testing solutions.
What is the exhibition about?
1518
[Page extract]
ASTM D413-98
ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.
1519
[Page extract]
BS EN 12814-4
BS EN 12814-4 is a peel test method for testing welded joints of thermoplastics semi-finished products.
1520
Case study
ISBT spor kapatma gerginlik testi
gereklilik Uluslararası İçecek Teknolojisi Uzmanları Derneği (ISBT) alkolsüz içeceklerin ve içeceklerin teknik ve bilimsel yönleri için gönüllü uygulama kodları yayınlamaktadır.
1521
[Page extract]
ISO 374-4
This document specifies the test method for the determination of the resistance of protective glove materials to degradation by dangerous chemicals with continuous contact.
1522
Case study
Cap removal test of plastic vial
Requirement
The customer approached Mecmesin with a specification to pull-off the cap of a pharmaceutical phial. The test equipment needed to be simple to use and able to perform repeatable tests.
1523
[Page extract]
Step-by-step procedure for reverse ratchet torque testing
Sample preparation
Condition the closures according to the specified standard to control environmental factors.
1524
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
1525
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells