Search results
726
[Page extract]
Introduction to flat crush test
The flat crush test (FCT) is a recognised method for measuring the resistance of corrugated fibreboard to a compressive load applied perpendicularly to its surface.
727
[Page extract]
Destructive and non-destructive methods
Testing may be performed destructively or non-destructively depending on the objectives.
728
[Page extract]
Methods for lap shear testing
Single lap shear test procedure
In a single lap shear test, two specimens are bonded with an adhesive in an overlapping configuration.
729
Case study
Bağlama kuvvetini test eden bağlı kapaklar
Gereksinim
Tüketiciler, üreticiler ve yasa koyucular daha çevreci ambalajlar talep ettikçe ve geri dönüştürülebilir malzemelerin kullanımı yaygınlaştıkça, dikkatler mütevazı plastik kapaklara çevrildi.
730
[Page extract]
Energy
Mecmesin has long been providing force and torque testing solutions to suppliers and contractors into the energy industry...
731
[Page extract]
Electrical switches and connectors
Switches and connectors may be low-cost simple electro-mechanical devices but they are ubiquitous in millions of products and devices we use every single day.
732
[Page extract]
bursting strength (sheet rupture)
Bursting strength is the capacity of a material or product to maintain in continuity when subjected to pressure.
733
Case study
Luer ve küçük delikli konektör Tork testi
gereklilik Sağlık uygulamalarındaki sıvılar ve gazlar için küçük delikli konektörlerle ilgili uluslararası standartlar, kullanım kolaylıklarına ve sızıntı veya yanlış kullanımlara karşı dirençlerine odaklanmaktadır.
734
[Page extract]
BS EN 868-5
Provides examples of particular requirements and test methods for heat and self-sealable pouches and reels manufactured from paper complying with EN 868-3 and plastic film complying with clause 4 of this European standard.
735
Event
Materials Testing: Theory and Practice Pt. 1 & 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
736
[Page extract]
ASTM D2646
These test methods may be used for acceptance testing of commercial shipments; however, caution is advised because information about between interlaboratory precision is incomplete. Comparative tests as directed in 5.1.1 may be advisable.
737
[Page extract]
BS EN ISO 16409
Describes performance criteria for manual interdental brushes with a round cross-section of the brush head and consisting of a wired stem with inserted filaents.
Of particular interest is the Stem Retention Force (sections 5.4 and 7.6)
738
[Page extract]
EN 149
EN149 specifies minimum requirements for filtering half masks as respiratory protective devices to protect against particles except for escape purposes.
740
[Page extract]
BS EN 564
Mountaineering equipment, Mountaineering ropes, Cords, Outdoor sports equipment, Sports equipment, Diameter, Tensile strength, Safety measures, Equipment safety, Marking, Instructions for use, Diameter measurement, Weight measurement
741
[Page extract]
ISO 594-2
ISO 594 and EN 1707 contain 8 separate tests, some of which are only applicable to Luer lock fittings. Most of these tests require that the sample be assembled to a particular precision steel reference fitting.
742
[Page extract]
BS EN 12453
BS EN 12453:2001 specifies the performance requirements with regard to the safety in use for any type of power operated doors, gates and barriers intended for installation in areas in the reach of persons, and for which the main intended uses are giving
743
[Page extract]
EEC 2006/42/EC
The Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 is a European Union directive concerning machinery and certain parts of machinery.[1] Its main intent is to ensure a common safety level in machinery placed on the mar
744
[Page extract]
BS EN 1607
This European Standard specifies the equipment and procedures for determining the tensile strength of a product perpendicular to its faces. It is applicable to thermal insulating products.
745
[Page extract]
ISO 16047
ISO 16047:2005 specifies the conditions for carrying out torque/clamp force tests on threaded fasteners and related parts.
746
[Page extract]
*corp 01M-01-217
To determine the maximum force required to rupture (break) a woven fabric.
747
[Page extract]
ISO 36
ISO 36 determines the strength required to separate two plies of fabric bonded together with rubber, or a rubber and a fabric ply bonded together. This test is referred to as a “T-peel” test, because as the two adherends are pulled apart, they form the
748
[Page extract]
ASTM D3032
These test methods detail the standard procedures for testing hookup wire insulations including all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness
749
[Page extract]
ISO 9073-3
Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.
750
[Page extract]
ISBT PTC-00004
These ISBT (International Society of Beverage Technologists) Sport Closure test methods focus on child safety related parameters such as separation forces and choking hazards of closure components.