Search results
1301
[Page extract]
ASTM and ISO approaches
ASTM D1938 specifies trouser tear testing for thin plastic films and sheeting, including specimen dimensions, pre-cu
1302
[Page extract]
BS EN ISO 6259-1
BS EN ISO 6259-1 is a test method for determining the tensile properties of thermoplastic pipes.
1303
[Page extract]
BS EN ISO 13934-1
Part 1 of ISO 13934 specifies a procedure to determine the maximum force and elongation at maximum force of textile fabrics using a strip method.
1304
Event
Essentials of Grip & Fixture Selection Pt. 2
The accuracy of instrument itself- though important, is only one piece of the measurement accuracy puzzle. Grip and fixture selection plays a critical role in the applications in Force and Materials quality testing.
1305
[Page extract]
ISO 6383-1
ISO 6383-1 specifies a method of determining the tear resistance of plastic film or sheet less than 1 mm thick, in the form of standard trouser-shaped test specimens, tested under defined conditions of pre-treatment, temperature, humidity, and speed of
1306
[Page extract]
ASTM C961
This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates.
1307
[Page extract]
BS EN 12310-1
Flexible materials, Sheet materials, Waterproofing materials, Construction materials, Tensile testing, Tear tests, Bitumens, Bituminous products, Roof coverings, Sheet roof coverings, Strength of materials, Test equipment, Specimen preparation
1308
[Page extract]
Get help with your products
Whether you're setting up a new test system or looking for documentation on an existing one, our online Support Center is the first place to start.
1309
[Page extract]
BS EN ISO 9000
ISO 9000 gives an overview of the fundamentals and concepts around quality management.
1310
[Page extract]
TAPPI T 809
This method describes a procedure for measuring the crushing resistance of a laboratory fluted strip of corrugating medium and provides a means of estimating, in the laboratory, the potential flat crush resistance of a corrugated board.
1311
[Page extract]
ASTM D7249-12
This test method covers determination of facing properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes and result in compressive and tensile forces in the
1313
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
1314
[Page extract]
SAE USCAR-38
This specification defines basic test methods and requirements for ultrasonically welded cable termination type connections.
1315
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
1316
[Page extract]
ISO 20795-1
ISO 20795-1:2013 classifies denture base polymers and copolymers and specifies their requirements. It also specifies the test methods to be used in determining compliance with these requirements.
1317
[Page extract]
ASTM D6484 / D6484M - 14
ASTM D6484 is a test method that determines the open-hole compressive strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibers.
1318
Event
Live Demonstration: Face mask strength testing & Syringe plunger breakaway force testing
Medical device testing ensures patient safety, regulatory compliance, performance, quality, usability, claims examination, and post-market safety.
1319
[Page extract]
ISO 505
ISO 505 specifies a method of test for the measurement of the propagation resistance of an initial tear in textile conveyor belts, either in full thickness or of the carcass only.
1320
[Page extract]
ASTM D3039 / D3039M
ASTM D3039 determines the in-plane tensile properties of polymer matrix composite materials reinforced by high-modulus fibers. A number of calculations can be made including ultimate tensile strength, ultimate tensile strain, tensile chord modulus of
1321
Case study
Surgical instrument operational torque
Customised engineering example
Endoscopic and laparoscopic surgical instruments are operated by axial and rotating adjustments in the handle, to perform precision movement in the head.
1322
[Page extract]
ASTM D4027-98
This test method describes equipment and procedures to measure the shear modulus and shear strength of adhesive layers between rigid adherends.
1323
[Page extract]
BS 2782-12: 1210A to C
BS 2782-12: Method 1210A to C specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.
1324
[Page extract]
BS EN 12814-1
BS EN 12814-1 is a bend test method for testing welded joints of thermoplastics semi-finished products.
1325
Event
Wine & Spirits Capping: Cork Pull & Twist Caps
Wine packaging has a great influence on the quality of the product delivered to the customer.