Search results
2426
[Page extract]
ISO 4049
This document specifies requirements for dental polymer-based restorative materials supplied in a form suitable for mechanical mixing, hand-mixing, or intra-oral and extra-oral external energy activation, and intended for use primarily for the direct or
2427
[Page extract]
BS 1726-3
Springs, Helical springs, Cylindrical shape, Torque, Circular shape, Wires, Bars (materials), Parallel, Dimensional tolerances, Form tolerances, Product specification, Ordering, Mechanical testing, Heat treatment
2428
[Page extract]
ASTM D5467 / D5467M-97
ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.
2429
Event
Webinar: Rice Texture Analyzer (Thai) - เทคโนโลยีเครื่องมือวัด และมาตรฐานการทดสอบข้าว
เทคโนโลยีเครื่องมือวัด และมาตรฐานการทดสอบข้าว
หนึ่งในปัจจัยที่สําคัญที่สุด ซึ่งมีผลต่อความสำเร็จของผลิตภัณฑ์ข้าวคือ เนื้อสัมผัส
เนื้อสัมผัสของข้าวส่งผลโดยตรงต่อความพึงพอใจของผู้บริโภค และความน่าเชื่อถือของผู้ผลิตข้าว นั่นคือเหตุผลว่า
2430
[Page extract]
IFI 143
This standard provides a test method for determining the torque-tension relationship on both external and internal threaded fasteners for the purpose of measuring the frictional characteristics of the threaded fasteners.
2431
[Page extract]
ASTM F806-99a
ASTM F806 is a test method that covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.
2432
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
2433
[Page extract]
ASTM C403/C403M
This test method covers the determination of the time of setting of concrete, with slump greater than zero, by means of penetration resistance measurements on mortar sieved from the concrete mixture.
2434
[Page extract]
ASTM D7078/D7078M-12
This test method covers the determination of the shear properties of high-modulus fiber-reinforced composite materials by clamping the ends of a V-notched specimen between two pairs of loading rails.
2435
[Page extract]
ISO 252
ISO 252 specifies two test methods, A and B, for determining the adhesion strength between constitutive elements of a conveyor belt, i.e. between plies and between covers and carcass.
2436
[Page extract]
BS ISO 6939
Applicable to spun single and folded yarns of any fibre or mixture of fibres manufactured by any spinning systems. Not recommended for testing filament yarns, glass yarns, more complex structures such as cabled yarns or cords.
2437
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
2438
[Page extract]
IEC 60598
IEC 60598-1 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V.
2439
[Page extract]
ISO 10373-1
ISO/IEC 10373-1:2006 specifies the non-technology-specific test methods required to establish conformance of identification cards to the base (requirements) standards, for which the fundamental properties are defined in ISO/IEC 7810.
2440
[Page extract]
BS 6319-11
BS 6319-11 is a test method for determining creep in compression and in tension for resin and polymer/cement compositions used in construction
2441
[Page extract]
ASTM D2731
ASTM D2731 is a test method for determining the elastic properties of elastomeric yarns made from rubber, spandex or other elastomers. Elastic properties include force at specified elongations, permanent deformation and stress decay.
2442
[Page extract]
ASTM D4760-91
This test method determines the proper resecuring of continuous thread child-resistant closures.
2443
[Page extract]
ISO 1966
Describes the design requirements and tests for the crimping of insulated and non-insulated terminations to general purpose cables, with conductors of copper, copper alloy, aluminium or aluminium alloy, in locations in which the stabilized conductor tem
2444
[Page extract]
BS EN ISO 22254
ISO 22254:2005 specifies a test method for determining the resistance of the tufted portion of manual toothbrushes to deflection. This could be used to derive a stiffness - a factor which has been of great concern to consumers and manufacturers.
2445
[Page extract]
ISO 2555
Specification of a method for determining an apparent viscosity of resins in a liquid state, using one of the types of rotational viskosimeter described in this standard.
2446
[Page extract]
BS EN ISO 6259-1
BS EN ISO 6259-1 is a test method for determining the tensile properties of thermoplastic pipes.
2447
[Page extract]
*corp 01M-01-218
To determine the resistance of seams to slip or break down when placed under a continuous load.
2448
[Page extract]
BS EN 455-2
Protective gloves, Protective clothing, Gloves, Surgical equipment, Sterile equipment, Disposable, Medical equipment, Dimensions, Length, Width, Ageing (materials), Strength of materials, Physical properties of materials, Physical testing
2449
[Page extract]
ASTM D4027-98
This test method describes equipment and procedures to measure the shear modulus and shear strength of adhesive layers between rigid adherends.
2450
[Page extract]
BS EN ISO 6892-1
This part of ISO 6892 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.