Search results
76
Case study
Syringe testing to ISO 11040-4 Annex G6 needle shield pull-off force
Requirement
The ubiquitous medical syringe is an extremely important device, delivering (parenteral) injectable products to the patient by means of a cylinder and plunger mechanism.
77
Case study
Spring design and manufacture
Requirement
Longcroft Engineering design and manufacture springs, from prototypes and hand-made custom designs, to high-volume production.
78
Case study
Electrical assembly component strength
Customised engineering example
Due to the complex, asymmetric shapes of electrical assemblies, it can be difficult to grip the soldered, fused and welded parts in a way that mimic the forces applied when in use.
79
[Page extract]
ASTM F3014-14
1.1 This test method describes the procedure for penetration testing sharp and blunt needles used for the placement of surgical sutures. It only describes the test procedures (Phase 1) and does not define a test medium at this time.
80
Case study
Wood for furniture and flooring large-scale bend and peel testing
Requirement
Lithuania's Klaipedos Mediena is a leading manufacturer of wooden furniture in Lithuania.
81
[Page extract]
Torque systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers? Do you want to reduce testing time and increase throughput for operators when performing batch tests?
82
Case study
Geosynthetic cementitious composite mat bend strength
Requirement
Concrete Canvas Ltd. utilises ground-breaking materials technology in their Concrete Canvas® GCCM product, which is essentially concrete on a roll.
83
Case study
Cable duct strength testing
Customised engineering example
Our customer manufactures tubes and ducts for routing of cables and optical fibres. Installation of these uses blowing, pushing and pulling techniques.
84
Case study
Screw-cap torque test on PET bottles
Requirement
For over a century, Agua de Luso has been one of Portugal's most famous names in mineral water.
85
Case study
Filter test station
Requirement
The following tests were required in a simple-to-use system for a series of tests on automotive filters:
86
Case study
Wire rope termination crimp safety
Requirement
TECNI Ltd., manufactures and supplies a range of steel, braided and wire rope assemblies for applications as diverse as security locks, balustrades, marine rigging, winching systems and gym equipment.
87
Case study
Insulation film stiffness testing
Customised engineering example
Familiar with three-point bending to test flexural strength properties?
88
Case study
Laminated auto windshield perimeter seal peel testing
Requirement
The windshield (or windscreen) in your car is made of laminated glass, which is designed to offer the highest levels of safety in the event of a crash.
89
Case study
Syringe testing to ISO 11040-4 Annex C1 flange break resistance
Requirement
The ubiquitous medical syringe is an extremely important device, delivering (parenteral) injectable products to the patient by means of a cylinder and plunger mechanism.
90
Case study
Scaffold support netting tester
Requirement
Huck, a scaffold netting supplier, run a return to manufacturer service to test netting has not degraded whilst in use.
91
Case study
Electrical harness terminal testing
Requirement
Cyprium Motorsports based in Diss, UK, design and produce customised wiring harness systems for sports cars, including Formula 1, Le Mans Prototype, Grand Touring and rally cars.
92
Case study
Fast food tray crush testing
Requirement
As a supplier of fast food trays, the customer needed to make sure that the trays would withstand a certain lateral force without damage to ensure they did not break when being handled and loaded with food.
93
Case study
Inline respiratory filter pull test
Customised engineering example
A manufacturer of filtration products needed to test the extraction force of a respiratory filter when pulled from within an inline medical device.
94
Case study
Torsion spring testing
Customised engineering example
Unlike most compression and tension springs, torsion springs are produced in a variety of forms with differing leg positions.
95
[Page extract]
ASTM E328-02
These test methods cover the determination of the time dependence of stress (stress relaxation) in materials and structures under conditions of approximately constant constraint, constant environment, and negligible vibration.
96
Case study
Leather ISO Testing to Strength, Elongation and Tear Resistance Methods
Requirement
One of the industry's largest tanners consulted Mecmesin as they wished to perform tensile tests on their leather materials in accordance with a number of international ISO standards.
97
Case study
Syringe testing to ISO 11040-4 Annex F needle penetration and drag
Requirement
The medical syringe is an extremely important device, delivering (parenteral) injectable products to the patient by means of a cylinder and plunger mechanism.
98
Case study
Needle to ferrule pull-out test
Requirement
The customer, Oxford Instruments, wished to perform a destructive pull-out test to evaluate the maximum tension force to pull the 2 components apart.
99
Case study
Safety critical welds in vehicle airbags
Requirement
The customer required an easy-to-use system for production staff on the factory floor. Testing needed to be carried out in the minimum amount of time with very little training.
100
Case study
Granule hardness test
Requirement
Ecosyl Products Limited is one of the world's leading companies involved in the sales and marketing of forage additives for the agricultural industry.