Search results
951
Accessory
Blank (smooth) jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 80 mm
Mec240k-B80
Blank Jaws (30mm x 80mm) - smooth steel jaw. Allows user to machine or affix own surface (eg. abrasive 'emery' paper).
Opening span = see datasheet for various spans according to the grip body selected.
Supplied as 0.5 set = 2 jaws (left…
952
Accessory
Wave jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 30 mm
Mec240k-BW
Wave Jaws (30mm x 30mm) - nickel-plated having a hardened steel surface of 5mm tall waves.
For flexible but slippy materials which need more surface contact to secure a good grip (e.g. textiles, fabrics and tissues).
Supplied as 0.5 set = 2 jaws (left…
953
Accessory
Wave jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 100 mm
Mec240k-BW100
Wave Jaws (30mm x 100mm) - nickel-plated having a hardened steel surface of 5mm tall waves.
For flexible but slippy materials which need more surface contact to secure a good grip (e.g. textiles, fabrics and tissues).
Supplied as 0.5 set = 2 jaws (left…
954
Accessory
V-jaws for 20 & 50kN Wedge Grip, round samples 4-16 mm
Mec243-BV16
V-Jaws (4-16mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods,
tubes).
Supplied as 0.5 set = 2 jaws (…
955
Accessory
Smooth jaws for 20 kN Scissor Grip, 10 kN, 25 x 100mm
Mec11-20-B100
Blank Jaws (25mm x 100mm) - smooth steel jaw. Allows user to machine or affix own surface. By using 100 mm width jaws tensile force is reduced to 10kN.
Supplied as 0.5 set = 2 jaws (left…
956
[Page extract]
Power your torque testing
Sophisticated power - easy to use
Looking for an automated torque testing system to improve the accuracy and repeatability of your measurements compared to manual torque testers?
957
[Page extract]
Plastic components and sub-assemblies
The successful design and production of plastic components requires careful attention to be paid to many elements. The choice of plastic material depends on the desired performance characteristics - will parts be under constant load?
958
[Page extract]
ASTM E1012-12e1
It has been shown that bending stresses that inadvertently occur due to misalignment between the applied force and the specimen axes during the application of tensile and compressive forces can affect the test results.
959
Event
Webinar: Adhesion/Peel strength testing
There is a reason people reach for duct tape as a fix for almost everything – adhesion strength.
From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufacturers.
960
[Page extract]
PD CEN/TR 17394-1
This document provides requirements for security of attachment for clothing components of infant clothing.
961
[Page extract]
ASTM D953-18
ASTM D953 is a test method that covers the determination of the pin-bearing strength of rigid plastics in either sheet form, molded form, or in reinforced thermoset form.
962
Case study
Tensile testing on polyethylene film
Requirement
Eurofilm Mantzaris S.A. are a leading producer of polyethylene films used for packaging and agricultural applications.
963
[Page extract]
ISO 4049
This document specifies requirements for dental polymer-based restorative materials supplied in a form suitable for mechanical mixing, hand-mixing, or intra-oral and extra-oral external energy activation, and intended for use primarily for the direct or
964
[Page extract]
BS 7548
Describes requirements and test methods for sterile syringes
with or without needles for single use solely for the injection
of insulin in humans. Covers syringes for use with 40 units of
965
Case study
End float test of inhaler cap
Requirement
'End float is the displacement in mm of a product', in this case the dispensing cap closure of the inhaler measured at a specific load.
966
Case study
Luer lock fastening and release torque
Customised engineering example
Luer lock test standards frequently call for measuring torque whilst simultaneously applying a pre-defined axial force.
967
Case study
Card and paper crease line testing
Customised engineering example
A packaging production company needed to test the crease force of the ink-coated card used in their fully-enclosed cartons.
968
Case study
ขวด PET ทดสอบบรรจุสูงสุด
ความต้องการ Esterform Packaging ผลิตขวด PET และพรีฟอร์มมากกว่าหนึ่งล้านขวดต่อวันสำหรับผู้ผลิตน้ำดื่มบรรจุขวดน้ำผลไม้น้ำอัดลมผลิตภัณฑ์นมและผลิตภัณฑ์ในครัวเรือน ในระหว่างการผลิต Esterform จำเป็นต้องสามารถประเมินความสามารถในการรับน้ำหนักตามแนวแก
970
[Page extract]
BS ISO 3597-2
ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.
971
[Page extract]
Why choose Mecmesin for floating roller peel testing
With decades of experience in materials and force measurement, Mecmesin offers robust and configurable systems that meet industry test standards while adapting to application-specific needs.
972
[Page extract]
Mecmesin solutions for equibiaxial flexure testing
Mecmesin designs and manufactures precision equipment for standards-compliant equibiaxial flexure compression testing, including the concentric ring method. Our systems combine robust mechanical design with advanced control and analysis software.
973
Case study
Tamper-Proof Closure Test
Requirement
Alcoa required a system to quickly test the tamper-proof rings on soft drink and mineral water closures.
The system had to be easy to operate and allow caps to be loaded quickly.
974
Case study
90 degree peel test filter paper
Customised engineering example
Floating roller peel jigs are regularly used for testing laminates where the backing sheet is rigid and the facing sheet is flexible (e.g. security cards)
975
Case study
Bulk liquid carrier closures
Customised engineering example
Our client manufactures liquid bulk carriers fitted with two-part plastic valve closures. The collar is welded to a plastic bag, and the valve closure is fixed onto it by a compression joint.