Search results
251
[Page extract]
Methods for lap shear testing
Single lap shear test procedure
In a single lap shear test, two specimens are bonded with an adhesive in an overlapping configuration.
252
[Page extract]
Introduction to the ring crush test
The ring crush test (RCT) is a key method for determining the edgewise compression strength of paper and paperboard.
253
[Page extract]
Industry-specific testing solutions
Strain at maximum stress testing is relevant wherever materials are expected to endure high loads without unacceptable deformation.
254
[Page extract]
Needle penetration and drag testing assess the force required to insert a needle into a material and the friction experienced during this process. This test ensures that syringes perform reliably, reducing risks to patients and healthcare providers.
255
[Page extract]
Understanding torque testing
Types of torque testing in packaging
Several torque measurements are relevant to closure performance:
256
[Page extract]
Applications in industry
Engineering and manufacturing uses
Tangent modulus testing supports design validation and process control in sectors where materials operate near or beyond the elastic range, for example:
257
[Page extract]
Case study – implementing VectorPro in packaging R&D
A packaging development team working with PLA (polylactic acid) bottles sought to optimise top-lo
258
[Page extract]
Applications of compression testing
Compression testing is essential for product development, quality assurance and compliance. Its applications span a wide range of industries and material types.
259
[Page extract]
Physiology
We exert force and torque with our muscles in almost all our everyday activities.
260
[Page extract]
Types of testing methods
Electromechanical and servohydraulic systems
Two main actuation technologies are used in tension and compression testing: electromechanical systems and servohydraulic systems.
261
[Page extract]
How tension testing is performed
Tensile strength testing
Tensile strength testing follows established international standards such as ISO 527 and ASTM D63
263
Event
Fundamentals of Food Texture Testing
Texture cannot be controlled unless it is measured in a consistent and repeatable manner.
264
[Page extract]
BS EN ISO 13262
BS EN ISO 13262 is test method to determine the tensile strength of seams on thermoplastics spirally-formed structured-wall pipes.
265
Event
Essentials of Consumer Packaging Testing
Maximize COST SAVINGS for your consumer packaging by minimizing excess material and “over design” while keeping your products protected in transit.
266
[Page extract]
ISO 8627
Specification of a test method and grading scheme for the stiffness of the tufted area of conventional manual tooth-brushes, together with the relevant information concerning definitions and those concerning testing machines.
268
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
269
[Page extract]
ISO 13939
Describes a method of comparing the performance test results of foil journal bearings, which are lubricated by air (gas) and supported by hydrodynamic force generated by the rotation of the rotating shaft.
270
[Page extract]
GS1 5.0
The Hanger Specifications are intended to increase efficiency in the supplier-to-retailer pipeline by minimizing order-to-sales floor cycle time.
271
[Page extract]
ASTM D2063/D2063M
This test method measures torque retention properties of container/continuous thread closure systems with the use of a non-automated, spring torque-meter (with either a dial indicator or a digital readout) or a torque wrench. evaluation.
272
[Page extract]
ASTM D5618-94
This test method covers the measurement of barnacle adhesion in shear to surfaces exposed in the marine environment. It is used to establish the ability of a surface to reduce biofouling adhesion.
273
Event
Materials Testing: Theory and Practice Pt. 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
274
Event
Torque, force, and texture testing: How to elevate cosmetic quality standards
Cosmetic products require testing for objective texture analysis as well as the performance of applicators, dispensers, and packaging.