Search results
2227
[Page extract]
BS 1726-1
Provides guidance on methods of specifying and tolerancing hot coiled compression springs, and cold coiled springs that fall outside the size range limits specified in BS EN 15800.
2228
[Page extract]
ASTM D2261
This test method covers the measurement of the tearing strength of textile fabrics by the tongue (single rip) procedure using a recording constant-rate-of-extension-type (CRE) tensile testing machine.
2229
[Page extract]
ISO 20795-1
ISO 20795-1:2013 classifies denture base polymers and copolymers and specifies their requirements. It also specifies the test methods to be used in determining compliance with these requirements.
2230
[Page extract]
ASTM C158
These test methods cover the determination of the modulus of rupture in bending of glass and glass-ceramics. These test methods are applicable to annealed and prestressed glasses and glass-ceramics available in varied forms.
2231
[Page extract]
ASTM D1321
This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.
2232
[Page extract]
ASTM D5448-11
This test method determines the inplane shear properties of wound polymer matrix composites reinforced by high-modulus continuous fibers. It describes testing of hoop wound (90°) cylinders in torsion for determination of inplane shear properties.
2233
[Page extract]
BS EN 12814-4
BS EN 12814-4 is a peel test method for testing welded joints of thermoplastics semi-finished products.
2234
[Page extract]
Why the ring crush test is critical for paperboard strength
Paperboard packaging must combine cost-efficiency with protective performance.
2235
[Page extract]
ASTM D1709-03
These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart.
2236
[Page extract]
BS EN 2747
BS EN 2747 is a tensile test method for testing carbon fibre reinforced plastics.
Before conducting BS EN 2747, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.
2237
[Page extract]
TAPPI T 402
Standard conditioning and testing atmospheres for paper, board, pulp handsheets, and related products, Test Method TAPPI/ANSI T 402 sp-13
2238
[Page extract]
BS EN ISO 314-1
This test standard specifies methods for determining the bonding quality of veneer plywood, blockboard and laminboard by shear testing.
2239
[Page extract]
ISO 2439
The indentation hardness of flexible cellular materials is a measure of their load-bearing properties.
2240
[Page extract]
Why torque testing is essential in packaging
Prevents leakage in liquid containers
Ensures seal integrity and prevents contamination
Confirms child-resistant closures are effective and compliant
Improves user experience by avoiding over-tightening
<
2242
[Page extract]
ANSI/EIA 364-38B
This standard establishes a test method to determine the axial tensile load that can be applied to a mated pair of connectors and the holding effect of a connector cable clamp without causing any detrimental effects upon the cable or connector when subj
2243
[Page extract]
ASTM D2105
ASTM D2105 determines the comparative longitudinal tensile properties of fiberglass pipe when tested under defined conditions of pretreatment, temperature, and testing machine speed.
2244
[Page extract]
BS EN 1270
Basketball equipment, Ball-games equipment, Sports equipment, Classification systems, Dimensions, Safety measures, Performance, Properties, Performance testing, Mechanical testing, Sports nets.
2245
[Page extract]
ASTM D2718
These test methods determine the shear properties of structural panels associated with shear distortion of the planes parallel to the edge planes of the panels. Both shear strength and modulus of rigidity may be determined.
2246
[Page extract]
Common challenges in yield point testing
Specimen alignment issues
Misalignment during clamping can cause uneven stress distribution, resulting in inaccurate readings.
2247
[Page extract]
VectorPro test definition
https://ahpublic.s3.eu-west-2.amazonaws.com/VectorPro/vcs/export/live/v…
2248
[Page extract]
ASTM D1000
These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows:
Class 1—Non-elastomeric backings made from materials
2249
[Page extract]
ISO 11608-5
This part of ISO 11608 specifies requirements and test methods for the automated functions of needle-based injection systems with automated functions (NIS-AUTO), for the administration of medicinal products in humans.
2250
[Page extract]
BS EN ISO 80369-1
BS EN ISO 80369 “Small-bore connectors for liquids and gases in healthcare applications. Connectors for intravascular or hypodermic applications”.
This standard replaces BS EN ISO 594-1: 1986, BS EN 20594-1:1994, and BS EN 1707:1997.