Search results
2576
[Page extract]
ASTM D7249-12
This test method covers determination of facing properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes and result in compressive and tensile forces in the
2577
[Page extract]
ASTM C165
1.1 This test method covers two procedures for determining the compressive resistance of thermal insulations.
2578
[Page extract]
ASTM E2658-15
These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices
2579
[Page extract]
IEC 60598
IEC 60598-1 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V.
2580
[Page extract]
ISO 1924-2
Specifies a method for measuring the tensile strength, strain at break and tensile energy absorption of paper and board, using a testing machine operating at a constant rate of elongation (20 mm/min).
2581
[Page extract]
BS 6319-3
BS 6319-3 is a test method for determining the modulus of elasticity in flexure and flexural strength of resin and polymer/cement compositions for use in construction.
2582
[Page extract]
ASTM F543-13
This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.
2583
[Page extract]
ASTM D5083-17
ASTM D5083 is a test method for measuring the force required to break a reinforced thermoset plastic specimen and the extent to which the specimen stretches or elongates to that breaking point.
2584
[Page extract]
ISO 10354
Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.
2585
[Page extract]
BS ISO 11752
BS ISO 11752 is a test method for determining the compressibility of flexible cellular polymeric materials.
2587
[Page extract]
TAPPI T 576
This test method decribes the procedure, using constant-rate-of-elongation, for determining three tensile breaking properties of towel and tissue: tensile strength, stretch, and tensi;e energy absorption.
2588
[Page extract]
ASTM D952-15
ASTM D952 is a test method that covers the determination of the bond strength or ply adhesion strength of sheet plastic and electrical insulating materials.
2589
[Page extract]
ISO 188
ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given:
2590
[Page extract]
*corp 01M-01-309
To determine the elongation and recovery properties of elastic Tapes (Both Woven and Knitted), reflectives, elastic tie cords Decorative TPU Bonding and Bonding Tape.
2591
[Page extract]
BS EN 13411-3
This European Standard deals with the requirements for ferrules for the ferrule-securing of eyes and endless loops - it applies to slings and assemblies using steel wire ropes for general lifting applications up to and including 60mm diameter conforming
2592
[Page extract]
BS EN 455-2
Protective gloves, Protective clothing, Gloves, Surgical equipment, Sterile equipment, Disposable, Medical equipment, Dimensions, Length, Width, Ageing (materials), Strength of materials, Physical properties of materials, Physical testing
2593
[Page extract]
BS EN ISO 6892-1
This part of ISO 6892 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.
2594
[Page extract]
Vice grip (Pneumatic)
Vice grips (single-action) - having one fixed jaw against which a second parallel jaw is tightened. The position of the fixed face may be adjustable to accommodate differing specimen thickness.
2595
[Page extract]
CETIE Guide 7
This guideline applies to the screw capping of still wines with a metallic closure having a threaded plastic insert and a tamper-evident band which needs to be snapped before it can be opened. The closure is screwed and crimped during capping.
2596
[Page extract]
USP <381>
This chapter applies to closures used for long-term storage of preparations defined in the general test chapter Packaging and Storage Requirements á659ñ, Injection Packaging.
2597
[Page extract]
ASTM D751-06
These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products.
2598
[Page extract]
ASTM D6534-05
This test method covers the determination of the peak force-to-actuate, sometimes called force-to-actuate (FTA), of a mechanical pump dispenser.
2599
[Page extract]
ISO 29862
This test standard specifies a series of methods for the determination of peel adhesion properties of self adhesives tapes.