Search results
2626
[Page extract]
ISO 4049
This document specifies requirements for dental polymer-based restorative materials supplied in a form suitable for mechanical mixing, hand-mixing, or intra-oral and extra-oral external energy activation, and intended for use primarily for the direct or
2627
[Page extract]
ISO 12192
Specifies a method for the determination of the edgewise compressive strength (ring crush resistance) of paper and paperboard, especially board used in the manufacture of fibreboard shipping containers.
2628
[Page extract]
ASTM D6713-14
Materials shall be tested and the individual grades shall conform to specified values of the physical properties such as tensile strength, tensile elongation, tensile modulus, dimensional stability, flexural modulus, and Izod impact; and dimensional pro
2629
[Page extract]
*corp QPF-MC-1209 B
*Strictly confidential*
L'Oreal to methods for shear and penetration testing of lipsticks, deodorants etc.
2630
[Page extract]
ASTM D4776 / D4776M-18
ASTM D4776 is a test method used to determine the maximum adhesion force of tyre cords in rubber compounds.
2631
[Page extract]
ISO 6789
Wrenches, Torque, Hand tools, Screwdrivers, Marking, Approval testing, Quality control, Calibration
2632
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
2633
[Page extract]
ASTM D6264 /D6264M-17
In ASTM D6264 a quasi-static indentation (QSI) test method is used to obtain quantitative measurements of the damage resistance of a continuous-fibre-reinforced composite material to a concentrated indentation force
2634
[Page extract]
BS EN 14350-1
Resusable teats and drinking accessories
Resusable feeding bottles and drinking cups
Single use feeding bottles, feeding teats, feeding bags and drinking accessories, which do not contain fluid when purchased.
2635
[Page extract]
TAPPI T 456
TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.
2636
[Page extract]
ASTM C403/C403M
This test method covers the determination of the time of setting of concrete, with slump greater than zero, by means of penetration resistance measurements on mortar sieved from the concrete mixture.
2637
[Page extract]
ASTM D5934-02
ASTM D5934 specifies the use of controlled rate of loading mechanical instrumentation on rectangular plastic bars molded directly or cut from sheets, plates, or molded shapes via three-point loading bending techniques to obtain material properties such
2638
[Page extract]
*corp 01M-01-216
To determine the maximum force required to rupture (break) a woven fabric – Rugby only
2639
[Page extract]
BS EN ISO 6789
Wrenches, Torque, Hand tools, Screwdrivers, Marking, Approval testing, Quality control, Calibration
2640
[Page extract]
ISO 10373-1
ISO/IEC 10373-1:2006 specifies the non-technology-specific test methods required to establish conformance of identification cards to the base (requirements) standards, for which the fundamental properties are defined in ISO/IEC 7810.
2641
[Page extract]
BS 6319-11
BS 6319-11 is a test method for determining creep in compression and in tension for resin and polymer/cement compositions used in construction
2642
[Page extract]
TAPPI T 284
This test evaluates the ability of corrugating medium to contribute to the compression strenght of a corrugated box.
2643
[Page extract]
ASTM D2731
ASTM D2731 is a test method for determining the elastic properties of elastomeric yarns made from rubber, spandex or other elastomers. Elastic properties include force at specified elongations, permanent deformation and stress decay.
2644
Specials
Vector instruments - Intuitive touchscreens
Intuitive touchscreen
The most advanced touchscreen force and torque gauges, powered by Vector OS.
Handheld instruments built for tough environments to deliver accuracy and reliability.
2645
[Page extract]
BS EN ISO 13262
BS EN ISO 13262 is test method to determine the tensile strength of seams on thermoplastics spirally-formed structured-wall pipes.
2646
[Page extract]
29 073-3
Textiles: test method for nonwovens; Part 3: Determination of tensile strength and elongation.
2647
[Page extract]
BS EN ISO 22088-2
BS EN ISO 22088-2 is a test method for determining the environmental stress cracking of plastics.
This has replaced BS EN ISO 6252:1998
2648
[Page extract]
ASTM D4032-08
This test method covers the determination of the stiffness of fabrics by the circular bend procedure. The method is generally applicable to all types of fabrics, including woven, knitted and nonwovens, of any fiber content.
2649
[Page extract]
BS EN 5350-C5
Adhesives, Test methods, Adhesive strength, Longitudinal, Strength of materials, Shear strength, Dimensional tolerances
2650
[Page extract]
ASTM D3164
Test method ASTM D3164 is used to produce shear strength data for joints to compare adhesives or evaluation surface treatments. Shear joints impose uniform stresses across the bond area which results in the highest possible joint strength.