Search results
1551
[Page extract]
SAE J1701
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user.
1552
[Page extract]
ASTM D3354
ASTM D3354 is a test method that provides quantitative information on the degree of blocking i.e. unwanted adhesion between layers of plastic film.
1553
[Page extract]
ISO 8033
ISO 8033 specifies methods for the determination of the adhesion between lining and reinforcement, between cover and reinforcement, between reinforcement layers, between cover and outer lamination (thin layer of material outside the cover for protection
1554
[Page extract]
BS EN 12814-2
BS EN 12814-2 is a tensile test method for testing welded joints of thermoplastics semi-finished products.
1555
[Page extract]
ASTM D6396-99
This test method covers procedures used to assemble, evaluate and test pipe thread sealants.
1556
[Page extract]
ASTM and ISO approaches
ASTM D1938 specifies trouser tear testing for thin plastic films and sheeting, including specimen dimensions, pre-cu
1557
[Page extract]
BS EN ISO 6259-1
BS EN ISO 6259-1 is a test method for determining the tensile properties of thermoplastic pipes.
1558
[Page extract]
BS EN ISO 13934-1
Part 1 of ISO 13934 specifies a procedure to determine the maximum force and elongation at maximum force of textile fabrics using a strip method.
1559
Case study
Pharmaceutical sachet burst strength
Customised engineering example
Plastic sachets with welded seams are frequently used for measured applications of liquids, creams and gels.
1560
[Page extract]
ASTM D349
These test methods cover the procedures for testing rigid round rods used in electrical insulation.
1561
[Page extract]
BS EN ISO 8339
This International Standard specifies a method for the determination of the tensile properties of sealants used in joints in building construction.
1562
[Page extract]
MIL AS23190A
AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment
1563
[Page extract]
Key properties measured in tensile testing
While ultimate tensile strength is the headline result, tensile testing also measures:
1564
[Page extract]
EN 149
EN149 specifies minimum requirements for filtering half masks as respiratory protective devices to protect against particles except for escape purposes.
1565
[Page extract]
BS EN ISO 9000
ISO 9000 gives an overview of the fundamentals and concepts around quality management.
1566
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
1567
[Page extract]
TAPPI T 809
This method describes a procedure for measuring the crushing resistance of a laboratory fluted strip of corrugating medium and provides a means of estimating, in the laboratory, the potential flat crush resistance of a corrugated board.
1568
[Page extract]
ASTM D7249-12
This test method covers determination of facing properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes and result in compressive and tensile forces in the
1569
[Page extract]
Get help with your products
Whether you're setting up a new test system or looking for documentation on an existing one, our online Support Center is the first place to start.
1570
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
1571
[Page extract]
ISO 20795-1
ISO 20795-1:2013 classifies denture base polymers and copolymers and specifies their requirements. It also specifies the test methods to be used in determining compliance with these requirements.
1572
[Page extract]
ASTM D6484 / D6484M - 14
ASTM D6484 is a test method that determines the open-hole compressive strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibers.
1573
[Page extract]
ISO 505
ISO 505 specifies a method of test for the measurement of the propagation resistance of an initial tear in textile conveyor belts, either in full thickness or of the carcass only.
1574
[Page extract]
ASTM D3039 / D3039M
ASTM D3039 determines the in-plane tensile properties of polymer matrix composite materials reinforced by high-modulus fibers. A number of calculations can be made including ultimate tensile strength, ultimate tensile strain, tensile chord modulus of
1575
[Page extract]
ASTM D4027-98
This test method describes equipment and procedures to measure the shear modulus and shear strength of adhesive layers between rigid adherends.