Search results
976
[Page extract]
What is top-load testing?
Top-load testing, also known as column crush testing, is a method used to evaluate the ability of a packaging component to withstand a vertical compressive force without deforming or failing.
977
Case study
Teste de rotação de boné esportivo ISBT
Requerimento A International Society of Beverage Technologists (ISBT) publica códigos de prática voluntários para os aspectos técnicos e científicos de refrigerantes e bebidas.
978
[Page extract]
Testing standards for secant modulus
Consistent measurement is supported by recognised standards:
979
[Page extract]
Testing methods and equipment
A cleavage strength test requires precise load application and accurate force measurement at the point of separation.
980
[Page extract]
Industry standards for torque to turn testing
There is no single universal standard for all torque to turn testing, but the method aligns with several sector-specific standards. Examples include:
981
[Page extract]
Introduction to friction and its importance
Friction is the resistive force that occurs when two surfaces interact. It plays a fundamental role in engineering and manufacturing.
982
[Page extract]
Accuracy and repeatability
Achieve a level of accuracy and repeatability that cannot be achieved by manual testers. Reduce your testing time and increase your throughput when performing batch tests.
983
[Page extract]
Standards for trapezoidal tear testing
Several international standards define this method, specifying specimen dimensions, slit length, and test speed. The most widely used include:
984
[Page extract]
Introduction to tension and compression testing
Tension and compression testing are among the most widely used mechanical testing methods for evaluating how a material or component performs under applied loads.
985
[Page extract]
Understanding shear testing in tension
Shear testing in tension is a mechanical method used to measure the resistance of a material or bonded joint to forces acting parallel to the bonding surface.
987
[Page extract]
Standards for flexural testing
Consistency in flexural strength testing is achieved through compliance with recognised standards, which define specimen dimensions, loading rates, and reporting requirements.
Key standards include:
988
[Page extract]
Introduction to pull-off and pull-out testing
Pull-off and pull-out testing are widely used to measure the strength, durability, and reliability of materials, adhesives, coatings, and mechanical fixings.
989
[Page extract]
Test standards for compressive strength
The main recognised standards for ring crush testing are:
990
[Page extract]
Key test standards
Grab method testing is governed by several internationally recognised standards, including:
991
[Page extract]
Test setup and equipment
Performing lap shear testing under compression requires careful alignment and use of appropriate fixtures to prevent torsion or uneven load distribution.
992
[Page extract]
Key standards
ASTM standards
ASTM D3470 - Procedures for measuring closure torque and assessing performance under applied stress
993
[Page extract]
Understanding compressive properties
Compressive properties describe how a material responds to being pressed, squeezed or compacted.
994
[Page extract]
Built for batch testing and automation
Batch testing in VectorPro uses a pre-configured test to create a semi-automatic or fully automatic testing system on sets of products and batches of the products.
995
Event
Wine & Spirits Capping: Cork Pull & Twist Caps
Wine packaging has a great influence on the quality of the product delivered to the customer.
996
Event
Fundamentals of Compression Testing
How much force is required to register a command when you click your computer mouse?
How much force can a water bottle take before it collapses in its case under a stack?
997
Event
Webinar: Essentials of Adhesion/Peel strength testing
There is a reason people reach for duct tape as a fix for almost everything – adhesion strength.
998
Event
Automotive Component Torque Testing
This webinar will focus on the measurement of the torque resistance in knobs, switches, and torsion springs, which are among several components in automobiles that require testing to ensure quality, performance, and safety.
999
Event
Tensile Testing: Extension, Elongation, Force & Failure
The primary objective for measuring and analyzing the the tensile force value of a product is to accurately determine one or more of these factors:
1000
Event
Webinar: Adhesion/Peel strength testing
There is a reason people reach for duct tape as a fix for almost everything – adhesion strength.
From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufacturers.