Search results
2426
[Page extract]
ASTM D349
These test methods cover the procedures for testing rigid round rods used in electrical insulation.
2427
[Page extract]
FINAT FTM 9
This test method describes a means of assessing probably the most important and yet the hardest to measure property of pressure sensitive materials, the tack.
2428
[Page extract]
EN 14488-2
Part 1: Sampling fresh and hardened concrete
Part 2: Compressive strength of young sprayed concrete
Part 3: Flexural strengths (first peak, ultimate and residual) of fibre reinforced beam specimens
2429
Case study
Ensaio de seringas de acordo com a norma ISO 11040-4 Anexo F, penetração e arrastamento da agulha
Requisitos
A seringa médica é um dispositivo extremamente importante, que fornece produtos injectáveis (parenterais) ao doente através de um mecanismo de cilindro e êmbolo.
2430
[Page extract]
ISO 4587
Specifies a method for determining the tensile lap-shear strength of rigid-to-rigid bonded assemblies using a standard specimen under specified conditions of preparation and testing. This test procedure does not provide design information.
2431
Case study
Torque de liberação de presilhas de tênis esportivos
Requerimento Um fornecedor líder de tênis de golfe precisava medir o torque de liberação das presilhas intercambiáveis em sua linha de calçados esportivos.
2432
Case study
Resistência à fratura da agulha da seringa sob cargas de flexão
Requerimento A Dong-A ST, com sede na Coréia do Sul, está se consolidando como uma empresa global no campo de medicamentos farmacêuticos éticos.
2433
[Page extract]
ASTM D6415 / D6415M-06a
ASTM D6415 is designed to measure the curved beam strength properties of fiber reinforced composites using a 90˚ curved beam specimen. The curved beam strength represents the moment per unit width which causes a delamination to form.
2434
[Page extract]
ASTM F2592
1.1 This test method covers the measurement of force displacement characteristics of a membrane switch.
2435
Case study
Teste de tração do filtro respiratório em linha
Exemplo de engenharia customizada Um fabricante de produtos de filtração precisava testar a força de extração de um filtro respiratório quando puxado de dentro de um dispositivo médico em linha.
2436
[Page extract]
ASTM D3044
This test method covers determination of the shear modulus of wood-based structural panels associated with shear distortion in the plane of the panels. The method is applicable to all types of wood-based structural panels.
2437
[Page extract]
ISO 13954
ISO 13954 describes a peel test method for determining the decohesive resistance of polyethylene electrofusion socket assemblies for use in the distribution of fluids.
2438
Case study
Características de torque de precisão da engrenagem amortecedora rotativa
Requerimento Um fabricante e distribuidor global de peças componentes que são usadas em produtos em muitos setores, incluindo transporte, beleza, bens de consumo e saúde, chegou à Mecmesin com uma aplicação desafiadora de medição de torque.
2439
[Page extract]
ISO 21180
ISO 21180 specifies a test method for the determination of the maximum tensile strength of light conveyor belts.
2440
[Page extract]
ASTM D4776 / D4776M-18
ASTM D4776 is a test method used to determine the maximum adhesion force of tyre cords in rubber compounds.
2441
[Page extract]
ISO 8094
ISO 8094 specifies a test method for determining the adhesion strength of the cover to the core layer. It applies exclusively to steel cord conveyor belts.
2442
[Page extract]
Understanding peel resistance
Peel resistance is the force required to separate two bonded surfaces through a peeling motion. This force is measured using a tensile test system equipped with a peel fixture.
2443
[Page extract]
ISO 10768
This International Standard specifies a test method for the determination of the resistance of elastic materials for footwear, to repeated extension produced during normal walking. The test can be carried out before and after accelerated ageing.
2444
[Page extract]
ASTM D3471
This test method covers the determination of the top-load required to engage lugs on Type IA child-resistant closures.
2445
[Page extract]
BS EN 12814-3
BS EN 12814-3 is a tensile creep test method for testing welded joints of thermoplastics semi-finished products.
2446
[Page extract]
Afera 5001
Self Adhesive Tapes - Measurement of Peel Adhesion from Stainless Steel or from its own Backing.
2447
[Page extract]
ASTM D1871
This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.
2449
[Page extract]
BS ISO 11752
BS ISO 11752 is a test method for determining the compressibility of flexible cellular polymeric materials.
2450
[Page extract]
ASTM D1566
ASTM D1566 is a source of reference for definitions of technical terms used in the rubber industry
Standards can be obtained from appropriate standard authorities.