Search results
1426
[Page extract]
Compression testing and its applications
Compression testing measures how a material behaves when subjected to forces that reduce its size.
1427
[Page extract]
Introduction to pull-off and pull-out testing
Pull-off and pull-out testing are widely used to measure the strength, durability, and reliability of materials, adhesives, coatings, and mechanical fixings.
1428
[Page extract]
Benefits of CMT testing for manufacturers
CMT testing offers multiple operational and commercial advantages:
1429
[Page extract]
Testing equipment and techniques
Mandrels
Custom-designed mandrels ensure closures are aligned and secured during testing. Correct mandrel design prevents slippage and eliminates fixture-induced variability.
1430
[Page extract]
Benefits and limitations of compressive shear testing
Advantages
High precision - accurate measurement of shear strength under controlled compression
<
1431
[Page extract]
Common challenges and best practices
Accurate four-point bend testing requires attention to several factors:
1432
[Page extract]
Why choose Mecmesin for compression testing?
Mecmesin has over 45 years of experience in force measurement and is a trusted partner for packaging test systems across industries.
1433
[Page extract]
Testing methods and equipment
A cleavage strength test requires precise load application and accurate force measurement at the point of separation.
1434
[Page extract]
Mechanical properties and accuracy considerations
Tensile testing via the strip method reveals mechanical properties that determine how fabrics perform in use.
1435
[Page extract]
Why choose Mecmesin for short span compression testing
Mecmesin provides complete solutions for short span compression testing, combining precision-engineered test frames, purpose-designed fixtures, and advanced control and analysis software.
1436
[Page extract]
Key test standards
Grab method testing is governed by several internationally recognised standards, including:
1437
[Page extract]
Understanding test types
Material testing uses a variety of methods to assess different mechanical properties. Selecting the right test depends on the intended application and relevant standards.
Examples include:
1438
[Page extract]
Mecmesin solutions for corrugated medium testing
Mecmesin offers flat crush testers and fixtures designed to meet TAPPI T 809 requirements.
1439
[Page extract]
Modulus of elasticity formula
Young’s modulus (E) is calculated from the linear portion of a stress-strain curve using this formula:
1440
Accessory
V-jaws for Mec154 Heavy-duty Vice Grip, 20kN, for round samples Ø 4-34 mm
Mec154-BV4
V-Jaws (4-34mm diameter with clamping height of 40mm) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods, tubes).…
1441
Accessory
Split Mandrel for Stelvin aluminium closure, mechanical
PDV14161
Half-round jaws with wire-eroded faces, for use with Vortex upper fixing plate (432-321). Specify closure diameter when ordering.
1442
Accessory
V-jaws for Mec240k Medium Vice Grip, 2.5 kN, for round samples Ø 3-52 mm
Mec240k-BV3
V-Jaws (3-52mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods,
tubes)
Supplied as 0.5 set = 2 jaws (…
1443
Accessory
V-jaws for 10kN Wedge Grip, for round samples 2 - 10 mm
MecS622-BV
V-Jaws (2-10mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove. For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods, tubes). Supplied as 0.5 set = 2 jaws (…
1444
Accessory
V-jaws for Mec240k Medium Vice Grip, 2.5 kN, for round samples Ø 2-52 mm
Mec240k-BV2
V-Jaws (2-52mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods, tubes)
Supplied as 0.5 set = 2 jaws (…
1445
Accessory
V-jaws for 20 & 50kN Wedge Grip, for round samples 3-13 mm
Mec243-BV
V-Jaws (3-13mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods, tubes).
Supplied as 0.5 set = 2 jaws…
1446
Accessory
V-jaws for 20 & 50kN Wedge Grip, for round samples 3-13 mm
Mec243-BV
V-Jaws (3-13mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods, tubes).
Supplied as 0.5 set = 2 jaws…
1447
Accessory
V-jaws for Mec240k Medium Vice Grip, 2.5 kN, for round samples Ø 3-52 mm
Mec240k-BV3
V-Jaws (3-52mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods,
tubes)
Supplied as 0.5 set = 2 jaws (…
1448
Accessory
V-jaws for Mec154 Heavy-duty Vice Grip, 20kN, for round samples Ø 4-34 mm
Mec154-BV4
V-Jaws (4-34mm diameter with clamping height of 40mm) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods, tubes).…
1449
Accessory
Split Mandrel for Stelvin aluminium closure, mechanical
PDV14161
Half-round jaws with wire-eroded faces, for use with Vortex upper fixing plate (432-321). Specify closure diameter when ordering.
1450
Accessory
V-jaws for Mec240k Medium Vice Grip, 2.5 kN, for round samples Ø 2-52 mm
Mec240k-BV2
V-Jaws (2-52mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods, tubes)
Supplied as 0.5 set = 2 jaws (…