Search results
1026
[Page extract]
BS EN ISO 13262
BS EN ISO 13262 is test method to determine the tensile strength of seams on thermoplastics spirally-formed structured-wall pipes.
1027
[Page extract]
BS EN ISO 6259-1
BS EN ISO 6259-1 is a test method for determining the tensile properties of thermoplastic pipes.
1028
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
1029
[Page extract]
BS EN ISO 6892-2
BS EN ISO 6892-2 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature.
1030
[Page extract]
ISO 8113
ISO 8113 specifies a method for determination of the resistance of glass containers to external force in the direction of the vertical axis.
1031
[Page extract]
ASTM D2105
ASTM D2105 determines the comparative longitudinal tensile properties of fiberglass pipe when tested under defined conditions of pretreatment, temperature, and testing machine speed.
1032
[Page extract]
BS 7907
BS 7907 gives recommendations for the design and manufacture of children’s clothing to promote mechanical safety. This standard is applicable to clothing intended for children up to 14 years of age.
1033
[Page extract]
ASTM D3163
ASTM D3163 is a test method used to determine the single-lap shear adhesive joints of rigid plastic adherends. The test method is useful for generating comparative shear strength data for joints made from a number of plastics.
1034
[Page extract]
ISO 13939
Describes a method of comparing the performance test results of foil journal bearings, which are lubricated by air (gas) and supported by hydrodynamic force generated by the rotation of the rotating shaft.
1036
[Page extract]
How tension testing is performed
Tensile strength testing
Tensile strength testing follows established international standards such as ISO 527 and ASTM D63
1037
[Page extract]
Bend jigs
Flexural load tests are popular since they closely characterise how a material or component may perform during its lifetime.
1038
[Page extract]
ASTM B533
The force required to separate a metallic coating from its plastic substrate is determined by the interaction of several factors: the generic type and quality of the plastic molding compound, the molding process, the process used to prepare the substrat
1039
Event
Critical strength: Perfecting catalyst and pellet crush testing
Catalysts are widely used in industrial processes where yield and time issues are critical to forming a product as soon as possible.
1040
[Page extract]
ASTM D4917-90
1.1 This test method describes a horizontal plane procedure for the determination of the coefficient of static and kinetic friction of paper measured when sliding against itself.
1041
[Page extract]
Education
Mecmesin testing solutions for education provide an affordable and ideal introduction to all forms of testing on design, materials science, engineering and even physiology courses.
1042
Software
VectorPro MT yazılımı
VectorPro® MT yazılımı
VectorPro MT, bir dizi malzeme üzerinde çekme, kesme, bükme ve sıkıştırma testleri gerçekleştirmek için geliştirilmiş gelişmiş bir malzeme test yazılımı paketidir. Ölçüm verilerini grafiksel olarak sunun ve özelleştirilmiş test…
1043
Article/Campaign
Test title
Tensile Testing Solutions
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Fusce ac ipsum varius, porttitor enim eu, porta ipsum. Quisque fermentum dolor est, in interdum purus tincidunt vitae.
1044
Article/Campaign
Test title
Top-load testing solutions
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Fusce ac ipsum varius, porttitor enim eu, porta ipsum. Quisque fermentum dolor est, in interdum purus tincidunt vitae.
1045
Specials
Extensometry low-force
Extensometer ready
Mecmesin's MultiTest-dV range supports extensometry in your testing methods when configured to run VectorPro™ MT materials testing software.
1046
Software
VectorPro Lite software (torque instruments)
VectorPro® Lite software
Available as an optional extra to Mecmesin's Orbis, Tornado and AFTI digital force and torque testing instruments, VectorPro Lite is an advanced data acquisition and plotting software package.
Simply select the appropriate…
1047
Specials
Extensometry single-column
Extensometer ready
Mecmesin's OmniTest single-column range supports extensometry in your testing methods.
1048
[Page extract]
Scissor grips
Scissor grips - self-tightening and self-aligning with the specimen initially being held by spring tension.
1049
Specials
Extensometry twin-column
Extensometer ready
Mecmesin's OmniTest twin-column range supports extensometry in your testing methods.
1050
Software
VectorPro Lite software (force instruments)
VectorPro® Lite software
Available as an optional extra to Mecmesin's Digital Force Gauges (VFG, AFG, BFG and CFG+ and VFTI/AFTI Digital Force Indicators, VectorPro Lite is an advanced data acquisition and plotting software package.
Simply select the…