Search results
1251
[Page extract]
Introduction to yield point testing
Yield point testing is essential for understanding the mechanical behaviour of materials.
1252
[Page extract]
BS EN ISO 844
ISO 844 specifies a method of determining a) the compressive strength and corresponding relative deformation, or b) the compressive stress at 10 % relative deformation, and c) when desired, the compressive modulus of rigid cellular plastics.
1253
[Page extract]
Importance of ergonomic strength testing
Ergonomic strength testing is essential for ensuring that human performance matches task requirements. This alignment reduces the risk of musculoskeletal injuries and improves long-term health outcomes.
1254
[Page extract]
CETIE Guide 3
This guide is for producers of quality sparkling wines who carry out the secondary fermentation process in the bottle, also known as bottle fermentation.
1255
[Page extract]
ASTM C1292
This test method covers the determination of shear strength of continuous fiber-reinforced ceramic composites (CFCCs) at ambient temperature.
1256
[Page extract]
ASTM D5034-09
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing.
1257
Bundle
Sharps puncture tester
OmniTest 2.5
BD001
A tester designed for key international standards such as ASTM F2132, BS 7320, and BS 23907 that specify the test procedures for puncture resistance of medical sharps containers.
1258
[Page extract]
Understanding compressive and tensile forces
Insertion and withdrawal testing focuses on two key force measurements:
1259
[Page extract]
Introduction to fabric testing
Fabric testing plays a critical role in quality assurance, helping manufacturers assess the mechanical, physical, and chemical properties of textile materials.
1260
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1261
[Page extract]
ISO 2493-1
Specifies procedures, based on the two-point loading principle, for determining the bending resistance of paper and board.
1262
[Page extract]
Introduction to double rip tongue tear testing
Double rip tongue tear testing is a recognised method for assessing the tear resistance of flexible materials including co
1263
[Page extract]
MIL 22520-G
This specification covers the general requirements for crimping tools, accessories and inspection gages used for connecting removable contacts (such as; signal, power, coaxial, shielded, thermocouple, and filter pin contacts) coaxial connectors, shielde
1264
[Page extract]
ASTM D6112-18
ASTM D6112 cover the determination of the creep and creep-rupture properties of plastic lumber and shapes, when loaded in compression or flexure under specified environmental conditions. Test specimens in the “as-manufactured” form are employed.
1265
[Page extract]
Mecmesin equipment for 90-degree peel testing
Mecmesin provides a range of test systems designed for peel and adhesion applications:
1266
[Page extract]
ASTM D6175-03
5.1 This test method is intended to provide information on the ability of an extruded catalyst to retain physical integrity during use.
1267
Test Frame
OmniTest test frame (single column)
OmniTest test frame
A single-column motorised test frame designed to apply tensile, shear, flexural and compressive forces from 2 N right up to a capacity of 7.5 kN (1686 lbf).Its versatile construction makes it perfectly suited for testing all kinds of…
1268
Event
Mecmesin Webinar: Introduction to consumer packaging testing
In the competitive world of consumer goods, damaged packaging isn't just a financial setback—it can tarnish your brand's reputation.
Customers are far less likely to choose a product with compromised packaging or one that arrives damaged due
1269
[Page extract]
Speak to an expert
Selecting the right trapezoidal tear testing setup requires understanding both the material and the relevant standards.
1270
[Page extract]
EN 22872
EN 22872 specifies two methods for testing complete, filled transport packages for compression resistance.
1271
[Page extract]
Introduction to pull-off and pull-out testing
Pull-off and pull-out testing are widely used to measure the strength, durability, and reliability of materials, adhesives, coatings, and mechanical fixings.
1272
[Page extract]
Three-point vs four-point bend testing
In a three-point bend test, force is applied at a single midpoint. In a four-point bend test, two loading noses distribute the load over a larger section of the specimen.
1274
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
1275
[Page extract]
Key properties measured in tensile testing
While ultimate tensile strength is the headline result, tensile testing also measures: