Search results
2701
[Page extract]
SAE AS7928
This specification covers insulated and uninsulated crimp-style copper terminal lugs and conductor splices for stranded conductors. An Amendment corresponding to this standard is available at AS7928_A1
2702
[Page extract]
BS EN 12562
Synthetic fibres, Polyamide fibres, Aramide fibres, Textile products, Textile testing, Yarn, Filament yarns, Filaments, Filament (textile fibre), Yarn testing, Yarn linear density determination, Elongation at fracture, Elongation, Force measurement, Mec
2703
[Page extract]
ISO 3377-2
ISO 3377-2:2016 specifies a method for determining the tear strength of leather using a double-edged tear. The method is sometimes described as the Baumann tear. It is applicable to all types of leather.
2704
[Page extract]
ASTM D1995
These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and
2705
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
2706
[Page extract]
TAPPI related
TAPPI Standards compared to Related Standards of ISO and ASTM (revised August 2011)
2707
[Page extract]
ISO 7439
ISO 7439:2002 is applicable to single-use copper-bearing intra-uterine contraceptive devices and their insertion instruments.
2708
[Page extract]
ASTM F806-99a
ASTM F806 is a test method that covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.
2709
[Page extract]
IPC TM-650
A suite of test methods for printed circuit boards. Visual, dimensional, chemical, mechanical, electrical, environmental. To determine the release strength of the carrier of thin copper foil in pounds per inch of width at ambient temperature
2710
[Page extract]
ISO 2555
Specification of a method for determining an apparent viscosity of resins in a liquid state, using one of the types of rotational viskosimeter described in this standard.
2711
[Page extract]
BS EN ISO 3376
This International Standard specifies a method for determining the tensile strength , elongation at a specified load and elongation at break. It is applicable to all types of leather
2712
[Page extract]
ASTM D3471
This test method covers the determination of the top-load required to engage lugs on Type IA child-resistant closures.
2713
[Page extract]
AEC Q200-005
This specification establishes the procedure and criteria to determine the ability of surface
mounted device terminations and seals to withstand bending, flexing and pulling forces which
2714
[Page extract]
ASTM D1871
This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.
2715
[Page extract]
TAPPI T 810
This method describes a procedure for measuring the bursting strength of single wall and double wall corrugated board within the range of 690 kPa (100psi) to 4825 kPa (700 psi) employing an instrument which uses a disk shaped, molded diaphragm.
2716
[Page extract]
ASTM D1566
ASTM D1566 is a source of reference for definitions of technical terms used in the rubber industry
Standards can be obtained from appropriate standard authorities.
2717
[Page extract]
ASTM E8/E8M-13a
These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area.
2718
[Page extract]
BS EN ISO 10590
This International Standard specifies a method for the determination of the influence of water immersion on the adhesion/cohesion properties at maintained extension of sealants used in joints in building construction.
2719
[Page extract]
BS EN ISO 6892-2
BS EN ISO 6892-2 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature.
2720
[Page extract]
TAPPI T 549
This method describes a horizontal plane procedure for the determination of the coefficient of static and kinetic friction of paper measured when sliding against itself.
2722
[Page extract]
BS EN 564
Mountaineering equipment, Mountaineering ropes, Cords, Outdoor sports equipment, Sports equipment, Diameter, Tensile strength, Safety measures, Equipment safety, Marking, Instructions for use, Diameter measurement, Weight measurement
2723
[Page extract]
ASTM D3822
This test method covers the measurement of tensile properties of natural and man-made single textile fibers of sufficient length to permit mounting test specimens in a tensile testing machine.
2724
[Page extract]
NF G30-102
La présente partie a pour objet de décrire une méthode de mesure directe de la pression de contention des garnitures élastiques telles que les bords-côtes de chaussettes, ceinturesde slips et de culottes, gaines et bas dits de confort, et plus généralem
2725
[Page extract]
ASTM D3518 / D3518M
ASTM D3518 is a test method, which measure the shear stress and shear strain properties of polymer matrix composite materials composed of +45 plies and -45° plies.