Search results
1976
[Page extract]
BS EN 28510-1
Test for measuring resistance to peeling at a nominal 90°, particularly suitable for adherends that are insufficiently flexible for a 180° peel test.
1977
[Page extract]
BS EN 2591-412
Covers a method of assessing the insertion/extraction forces for contacts used in elements of connection.
1978
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
1979
[Page extract]
CETIE Guide 6
This guide gives information on good practice for bottling still wine with an aluminium screw caps on a BVS type glass finish according to EN 16293, with redraw of the cap on application.
1980
[Page extract]
ASTM F543-13
This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.
1981
Product
Manuel test standı
MDD Hassas El Çarkı
804-001
Elle çalıştırılan test standları kompakt, portatiftir ve ergonomik kullanım için tezgah üzerine monte edilebilir. 1000 N'ye kadar gerginliği ve kompresyonu ölçmek için herhangi bir Mecmesin dijital kuvvet ölçer ile birleştirin. Kuvvet ölçer ayrı…
1982
[Page extract]
ASTM F628-12e3
This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipes made to Schedule 40 iron pipe sizes (IPS) with concentric inner and outer solid ABS layers and a closed-cell cellular ABS core.
1983
[Page extract]
ASTM D3528
This test method covers the determination of the tensile shear strengths of adhesives for bonding metals when tested in an essentially peel-free standard specimen that develops adhesive stress distribution representative of that developed in a typical l
1984
[Page extract]
TAPPI T 825
The flat crush test (1) is a measure of the resistance of the flutes in corrugated board to a crushing force applied perpendicular to the surface of the board under prescribed conditions.
1985
[Page extract]
ASTM D622-99
ASTM D622 is a test method intended for use in testing the conventional types of hose employed for the operation of air brake and vacuum brake systems, either on a single motor vehicle or as connecting or transmission lines in a combination of vehicles<
1987
[Page extract]
ISO 11747
ISO 11747 specifies a method for the determination of resistance to extrusion of milled rice kernels, parboiled or not parboiled, after cooking under specified conditions.
1988
[Page extract]
ISO 1827
ISO 1827 specifies methods for the determination of the modulus in shear and the strength of bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates.
1989
[Page extract]
ASTM D4475-02
ASTM D4475 is a test method used for determining the horizontal shear strength of fiber reinforced plastic rods.
1990
[Page extract]
ISO 505
ISO 505 specifies a method of test for the measurement of the propagation resistance of an initial tear in textile conveyor belts, either in full thickness or of the carcass only.
1991
Event
Packaging: Peel & Adhesion testing
Adhesion strength is a key factor in packaging, providing reliability and durability for a wide range of products.
Whether it's ensuring that a shipping box remains sealed during transit or that labels stay firmly attached to containers, the a
1992
[Page extract]
BS 2782-12: 1210A to C
BS 2782-12: Method 1210A to C specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.
1993
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1994
[Page extract]
BS EN ISO 13934-2
Part 2 of ISO 13934-2 specifies a procedure for the determination of the maximum force of textile fabrics known as the grab test.
1996
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
1997
[Page extract]
ISO 6237
Specifies a method for determining the shear strength of wood-to-wood adhesive bonds, with a standard specimen loaded in tension and under specified conditions of preparation, conditioning and testing.
1998
[Page extract]
FINAT FTM3
This test method allows the end user to determine the force required to separate the release backing from the pressure sensitive adhesive coated face material.
1999
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
2000
[Page extract]
ASTM D3410 / D3410M
ASTM D3410 determines the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.