Mecmesin | Search results

2101

Product

Püskürtme beton ilk basınç dayanımı test cihazı

Püskürtme beton Penetrometresi

850-611

Püskürtme beton Penetrometresi , BS EN 14488-2'ye (Metot A) göre genç püskürtülen betonun ilk kürleme aşamasının basınç dayanımını test etmek için komple bir taşınabilir sistemdir. Püskürtülen (püskürtme beton) veya dökülen betona nüfuz etmek için…

2102

^{[Page extract]}

ASTM F543-13

This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.

2103

^{[Page extract]}

ASTM D6415 / D6415M-06a

ASTM D6415 is designed to measure the curved beam strength properties of fiber reinforced composites using a 90˚ curved beam specimen. The curved beam strength represents the moment per unit width which causes a delamination to form.

2104

^{[Page extract]}

ASTM D6264 /D6264M-17

In ASTM D6264 a quasi-static indentation (QSI) test method is used to obtain quantitative measurements of the damage resistance of a continuous-fibre-reinforced composite material to a concentrated indentation force

2105

^{[Page extract]}

TAPPI T 807

This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).

2106

^{[Page extract]}

ISO 13954

ISO 13954 describes a peel test method for determining the decohesive resistance of polyethylene electrofusion socket assemblies for use in the distribution of fluids.

2107

^{[Page extract]}

BS EN ISO 4074

BS EN ISO 4074:2002 specifies the minimum requirements and the test methods to be used for condoms made from natural rubber latex which are supplied to consumers for contraceptive purposes and to assist in the prevention of sexually transmitted infectio

2108

^{[Page extract]}

ASTM C165

1.1 This test method covers two procedures for determining the compressive resistance of thermal insulations.

2109

^{[Page extract]}

ASTM D906-98

The way adhesives are used in plywood makes shear strength an important performance criteria. Shear strength measured by this test is suitable for use in adhesive development, manufacturing quality control, and in materials performance specifications.

2110

^{[Page extract]}

ASTM D 2979

1.1 This test method covers measurement of the pressure sensitive tack of adhesives.

2111

^{[Page extract]}

ASTM D4475-02

ASTM D4475 is a test method used for determining the horizontal shear strength of fiber reinforced plastic rods.

2112

^{[Page extract]}

ASTM D380

ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.

2113

^{[Page extract]}

SAE AS22520-G

Relevant to 4.7.11 only: tensile strength.

2114

^{[Page extract]}

ASTM D412-16

ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.

2115

^{[Page extract]}

ASTM D4964-96

5.1 This test method for testing loop tension and elongation of elastic fabrics is considered satisfactory for acceptance testing of commercial shipments of elastic fabrics because the test method is used in the trade for acceptance testing.

2116

^{[Page extract]}

EN 14488-2

Part 1: Sampling fresh and hardened concrete Part 2: Compressive strength of young sprayed concrete Part 3: Flexural strengths (first peak, ultimate and residual) of fibre reinforced beam specimens

2117

Event

Introduction to Consumer Packaging Testing

Damaged packaging can not only cost money but also impact brand perception. Consumers are less likely to purchase a product with damaged packaging, or if their product arrives damaged from poor packaging during the shipping and transport process.

2118

Product

Tork tornavida kontrol kalibratörü

TSCC

TSCC , 10 Nm'ye kadar önceden ayarlanmış ve ayarlanabilir tork sınırlayıcı tornavidaların kalibrasyonunu kontrol etmek için yarı otomatik bir test sistemidir. Önceden programlanmış testler ve tek dokunuşla çalıştırma ile TSCC, sonuçlardaki…

2119

^{[Page extract]}

ASTM D3164

Test method ASTM D3164 is used to produce shear strength data for joints to compare adhesives or evaluation surface treatments. Shear joints impose uniform stresses across the bond area which results in the highest possible joint strength.

2120

^{[Page extract]}

SAE AMSSTD

This standard covers the general requirements and methods for testing sandwich core materials and for testing sandwich construction of the types used primarily in aircraft structures.

2121