Search results
2026
[Page extract]
ISO 8362-7
This part of ISO 8362 specifies aluminium-plastics combinations for the injection caps of injection vials, as specified in ISO 8362-1 and ISO 8362-4, where the plastics part does not overlap the diameter of the vial body. Section 6.2 Force required to
2027
[Page extract]
BS EN 28510-1
Test for measuring resistance to peeling at a nominal 90°, particularly suitable for adherends that are insufficiently flexible for a 180° peel test.
2028
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
2029
[Page extract]
BS EN 71-1
This European Standard specifies different forces or loads to be used when testing toys intended for children of different age groups.
2030
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
2031
[Page extract]
ASTM F2606-08
This guide can be used to obtain force versus deflection or midspan bending moment versus midspan curvature curves for stents and stent systems subjected to three-point bending conditions.
2032
[Page extract]
ASTM D5467 / D5467M-97
ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.
2033
[Page extract]
TAPPI T 825
The flat crush test (1) is a measure of the resistance of the flutes in corrugated board to a crushing force applied perpendicular to the surface of the board under prescribed conditions.
2034
[Page extract]
ISO 1798
ISO 1798 specifies a method for determining the strength and deformation properties of flexible cellular materials when a test piece is extended at a constant rate until it breaks.
This test standard is equivalent to BS EN ISO 1798:2008
2035
[Page extract]
ASTM D3039 / D3039M
ASTM D3039 determines the in-plane tensile properties of polymer matrix composite materials reinforced by high-modulus fibers. A number of calculations can be made including ultimate tensile strength, ultimate tensile strain, tensile chord modulus of
2036
Event
Packaging: Peel & Adhesion testing
Adhesion strength is a key factor in packaging, providing reliability and durability for a wide range of products.
Whether it's ensuring that a shipping box remains sealed during transit or that labels stay firmly attached to containers, the a
2037
[Page extract]
BS EN 12311-2
BS EN 12311-2 is a test method for determining the tensile properties of flexible sheets used for waterproofing roofs.
2038
[Page extract]
BS EN 1393
BS EN 1393 specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.
2039
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
2040
[Page extract]
PSTC 131
SCOPE
1.1 The procedures in this test method describe the measurement of breaking strength, elongation
at break, and energy to break, of pressure sensitive tapes.
2041
[Page extract]
Tork testi
Tork testi, bir nesnenin döndürüldüğünde nasıl tepki vereceğini belirlemenin bir yoludur - normal çalışma sırasında veya kasıtlı olarak arızalanana veya kırılana kadar b
2042
Event
Essentials of Adhesion (Peel) Testing
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
2043
[Page extract]
BS EN ISO 13934-2
Part 2 of ISO 13934-2 specifies a procedure for the determination of the maximum force of textile fabrics known as the grab test.
2044
[Page extract]
*corp QAC-MC-844
Confidential to l'Oreal
The aim of this test is to check that folding boxes form properly so as to ensure their fluidity of distribution on the filling and packing lines.
2045
[Page extract]
ASTM D229
ASTM D229 is a test method, which provides useful engineering information for evaluating the mechanical behaviour of rigid electrical insulation at elevated temperature.
2046
[Page extract]
ASTM D5379/D5379M-05
This test method covers the shear properties of composite materials reinforced by high-modulus fibers. The composite materials are limited to continuous-fiber or discontinuous-fiber-reinforced composites in specific forms.
2047
[Page extract]
ISO 6237
Specifies a method for determining the shear strength of wood-to-wood adhesive bonds, with a standard specimen loaded in tension and under specified conditions of preparation, conditioning and testing.
2048
[Page extract]
ASTM D2105
ASTM D2105 determines the comparative longitudinal tensile properties of fiberglass pipe when tested under defined conditions of pretreatment, temperature, and testing machine speed.
2049
Product
Tork anahtarı kalibratörü
TWC
875-001
TWC Tork Anahtarı Kalibratörü standart 'kiriş', 'klik' ve 'koparma' anahtarlarındaki ayarları kontrol etmek için basit ve uygun maliyetli bir çözümdür. Her bir anahtar için sonuçları kaydetmek için RS232 veri çıkışı ile 1000 Nm…
2050
Event
Wire Terminal Strength & Crimp Testing Webinar
The only way of really knowing the strength of a crimped terminal is to pull it.