Search results
1976
Case study
ISO 11608-3'e göre önceden doldurulmuş ilaç kartuşlarının kırılma ve sürdürme kuvveti testleri
gereklilik İnsülin gibi ilaçların dağıtımı için mekanik kalem enjektörler, geleneksel şişe ve şırınga yöntemine göre artan bir kabul görmüştür.
1977
Case study
Şarap açma kuvvetini patlatabilir ve yırtabilir
Gereklilik Geleneksel şarap uzmanı, kapaklar açısından bir ambalaj evrimi gördü; doğal mantardan sentetik mantar malzemelerine, Stelvin® vidalı kapaklara.
1978
Case study
Pişmiş pirinç sertliği yapışkanlık ve yapışkanlık
Gereksinim
Pirincin dokusu, tüketicinin ürünün kalitesini nasıl algıladığı konusunda hayati önem taşır. Doku, kabul için kritik öneme sahip duyusal kriterlerden biridir.
1979
Case study
Pişmiş pirinç sertliği yapışkanlık ve yapışkanlık
Gereksinim
Pirincin dokusu, tüketicinin ürünün kalitesini nasıl algıladığı konusunda hayati önem taşır. Doku, kabul için kritik öneme sahip duyusal kriterlerden biridir.
1980
[Page extract]
ASTM D413-98
ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.
1981
[Page extract]
ISO 9073-3
Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.
1982
[Page extract]
BS EN ISO 8295
ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr
1983
Product
Otomatik şişe kapatma test cihazı
ABC-t
ABC-t , tam bir sargıya dayanıklı rulo (ROPP) kapağı grubunun hem başlangıç kaymasını hem de köprü torkunu ölçmek için otomatik bir şişe kapatma test cihazıdır. Kapakların otomatik toplu testi, test süresi boyunca bir operatöre ihtiyaç duymadan…
1984
Event
Wire Crimp & Weld Testing Webinar
The only way of really knowing the strength of a crimped terminal is to pull it.
1985
[Page extract]
ASTM D3983
This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.
1986
Product
Manuel test standı
MDD Hassas El Çarkı
804-001
Elle çalıştırılan test standları kompakt, portatiftir ve ergonomik kullanım için tezgah üzerine monte edilebilir. 1000 N'ye kadar gerginliği ve kompresyonu ölçmek için herhangi bir Mecmesin dijital kuvvet ölçer ile birleştirin. Kuvvet ölçer ayrı…
1987
[Page extract]
DIN EN 1464
This European Standard specifies a floating roller method for the determination of the peel resistance of high-strength adhesive bonds between one rigid adherend and one flexible adherend when tested under specified conditions of preparation and testing
1988
[Page extract]
ISO 1805
ISO 1805 specifies a method of testing the breaking force and knot breaking force of netting yarns for fishing nets.
1989
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
1990
[Page extract]
TAPPI T 400
This method describes procedures for obtaining a representative sample for testing.
1991
[Page extract]
BS 6319-11
BS 6319-11 is a test method for determining creep in compression and in tension for resin and polymer/cement compositions used in construction
1992
[Page extract]
BS 7882
This British Standard specifies the requirements for the calibration and classification of torque measuring devices including those used for the calibration of hand torque tools to BS EN 26789: 1994/
1993
[Page extract]
ASTM D5034-09
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing.
1994
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
1995
[Page extract]
FINAT FTM3
This test method allows the end user to determine the force required to separate the release backing from the pressure sensitive adhesive coated face material.
1996
[Page extract]
ASTM D3528
This test method covers the determination of the tensile shear strengths of adhesives for bonding metals when tested in an essentially peel-free standard specimen that develops adhesive stress distribution representative of that developed in a typical l
1997
Product
Kas gücü test cihazı
Myometer
850-030
Mecmesin Myometer , çok çeşitli kas gücü değerlendirmeleri ve ergonomik testlere uygun, son derece hassas bir cihazdır. Tıp uzmanları ile ortaklaşa geliştirilen bu özel cihaz, daha tutarlı sabit nokta izometrik kas gücü testleri gerçekleştirebilir.…
1998
[Page extract]
ASTM D622-99
ASTM D622 is a test method intended for use in testing the conventional types of hose employed for the operation of air brake and vacuum brake systems, either on a single motor vehicle or as connecting or transmission lines in a combination of vehicles<
1999
[Page extract]
ISO 11747
ISO 11747 specifies a method for the determination of resistance to extrusion of milled rice kernels, parboiled or not parboiled, after cooking under specified conditions.