Search results
2451
[Page extract]
Support
Our sales, engineering and technical support teams are committed to providing the highest level of customer service. Mecmesin provide application and technical support for all of our products.
2452
[Page extract]
ASTM D1938
ASTM D1938 covers the determination of the force necessary to propagate a tear in plastic film and thin sheeting by a single-tear method. It rates the tear-propagation resistance of various plastic films and thin sheeting of comparable thickness.
2453
Case study
İnfüzyon solüsyon torbasının uzama testi
gereklilik Fresenius Kabi, infüzyon terapileri ve klinik beslenme için global bir farmasötik ürün ve dağıtım sistemi üreticisidir.
2454
[Page extract]
ISO 7810
Stipulates test method as per ISO/IEC 10373-1 for determining the Peel Strength of cards.
2455
[Page extract]
BS EN ISO 1806
This standard specifies a method of determining the mesh breaking force of netting for fishing.
2456
[Page extract]
ASTM D3787
This test method describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation.
2457
Case study
Tıbbi kılavuz tel kopma mukavemeti testi
gereklilik Şirket, kardiyo, endo ve nörovasküler uygulamalar için minimal invaziv cihazlarda kullanılan tel oluşturulmuş tıbbi cihaz ve bileşen üreticisidir.
2458
Case study
Plastik phial kapak çıkarma testi
gereklilik Müşteri, Mecmesin'e farmasötik bir şişenin kapağını çıkarmak için bir spesifikasyonla yaklaştı. Test ekipmanının kullanımı basit olmalı ve tekrarlanabilir testler yapabilmelidir.
2459
[Page extract]
ISO 11502
Describes a qualitative and a quantitative method for assessing the tendency of flexible plastics films and sheets to adhere to one another when left in contact for some time, at a specified temperature and under light pressure.
2460
[Page extract]
ISO 252
ISO 252 specifies two test methods, A and B, for determining the adhesion strength between constitutive elements of a conveyor belt, i.e. between plies and between covers and carcass.
2461
Event
Introduction to Consumer Packaging Testing
Damaged packaging can not only cost money but also impact brand perception. Consumers are less likely to purchase a product with damaged packaging, or if their product arrives damaged from poor packaging during the shipping and transport process.
2462
[Page extract]
SAE J 1523
This SAE Recommended Practice defines a procedure for determining shear strengths of adhesives used for bonding automotive oil metal substrates.
2463
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
2464
[Page extract]
TAPPI T 804
This method is used for measuring the ability of corrugated or solid fiber shipping containers to resist external compressive forces.
2465
[Page extract]
ISO 813
ISO 813 specifies a method for the determination of the adhesive strength of a vulcanized or thermoplastic rubber bonded to a rigid substrate, using a test piece comprising a strip of rubber bonded to a single plate of rigid material.
2466
[Page extract]
ASTM E855-08
This standard describes three test methods for determining the modulus of elasticity in bending and the bending strength of metallic strips or sheets intended for the use in flat springs.
2467
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
2468
[Page extract]
TAPPI T 807
This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).
2469
[Page extract]
Claw grips
Claw grips and chucks - designed to either grip a cylindrical test specimen directly, or to grip a thin probe, such as a needle for penetration testing.
Often used to help grip irregular shaped objects.
2470
[Page extract]
Üniversal test cihazları
Üniversal test cihazlarımız (UTM), uluslararası ve sektöre özgü standartlara uygun olarak çekme ve sıkıştırma testleri de dahil olmak üzere bir dizi test gerçekleştirebilir.
2471
Event
Essentials of Grip & Fixture Selection Pt. 2
The accuracy of instrument itself- though important, is only one piece of the measurement accuracy puzzle. Grip and fixture selection plays a critical role in the applications in Force and Materials quality testing.
2472
[Page extract]
BS EN 12814-4
BS EN 12814-4 is a peel test method for testing welded joints of thermoplastics semi-finished products.
2473
Case study
Peel testing Ostomy bags
Requirement
Salts Healthcare, a leading manufacturer and supplier of health care products required a low capacity system for testing the integrity of their hydrocolloid products.
2474
Case study
Elektrikli montaj bileşen gücü
Özel mühendislik örneği Elektrik montajlarının karmaşık, asimetrik şekilleri nedeniyle, lehimlenmiş, kaynaşmış ve kaynaklı parçaları kullanım sırasında uygulanan kuvvetleri taklit edecek şekilde kavramak zor olabilir.
2475
[Page extract]
BS EN ISO 21181
BS EN ISO 21181 is a test method for determining the relaxed elastic modulus of light conveyor belts.