Search results
1376
Case study
Elmas uçlu taşlama ve kesici takım kopma mukavemeti
gereklilik Otomotiv, BT ve elektronik dahil olmak üzere çeşitli endüstrilerde son derece hassas ve yüksek dereceli işleme sağlayan elmas aletler kullanılmaktadır.
1378
Case study
Child resistant closures (CRC) mandrel
Customised engineering example
Child Resistant Closures (CRC) require sufficient vertical force to activate the CR locking mechanism prior to torque being applied.
1379
[Page extract]
Common test methods and standards
Internationally recognised standards ensure that compressibility and recovery testing is consistent and repeatable across laboratories and production sites.
1380
[Page extract]
Measurement and testing methods
Techniques for measuring tangent modulus
Tangent modulus is measured during tensile or compression testing, w
1381
[Page extract]
Applications across industries
Compressive hardness testing is applied in many sectors to confirm that materials meet performance and safety criteria.
1382
[Page extract]
Understanding the stress-strain curve
The stress-strain curve is a primary tool for tensile strength analysis. It shows how a material responds to an increasing tensile load, providing detailed insights into its mechanical properties.
1383
[Page extract]
Introduction to yield point testing
Yield point testing is essential for understanding the mechanical behaviour of materials.
1384
[Page extract]
Speak to an expert
Choosing the right configuration for a peel test is essential to obtain meaningful data. Test speed, specimen type, fixture design and data analysis all influence the results.
1385
Case study
Medical devices testing
Requirement
To provide a low cost, flexible tensile test machine which could be used in conjunction with special fixturing, to perform a range of functional and destructive tests on a range of products.
1386
[Page extract]
Introduction to elongation and recovery testing
In industries working with textiles, rubber, elastomers, and flexible plastics, these properties are directly linked to product reli
1387
[Page extract]
How the strip method works
The strip method involves cutting a specimen to a precise width, typically 50 mm or 25 mm depending on the applicable standard, and mounting it in the grips of a tensile testing
1388
[Page extract]
BS EN 12209
BS EN 12209:2016 specifies requirements and test methods for the durability, strength, security, and function of mechanically operated locks and latches and their locking plates for use in doors, window doors and entrance doors in buildings.
1389
[Page extract]
Speak to an expert
Cleavage strength testing is essential for confirming material and adhesive performance in demanding applications.
1390
[Page extract]
Peel test procedure - step by step
Prepare the specimen: Cut and condition according to the relevant standard.
Set up the machine: Install the correct fixture for the test type.
1391
Case study
Champagne and sparkling wine cork twist extraction effort
Requirement
Solution
Test equipment
1392
[Page extract]
Understanding peel resistance
Peel resistance is the force required to separate two bonded surfaces through a peeling motion. This force is measured using a tensile test system equipped with a peel fixture.
1393
Event
Webinar: Master Grips & Fixtures for Consistent Testing
When physically testing a material or component, the ability to apply load to a test specimen is important—but having the ability to apply that load correctly is just as crucial.
1394
Case study
Ruj tüpü kuvveti ve tork testi
gereklilik Ruj, dünya çapında her yıl satılan 800 milyondan fazla tüp ile en popüler kozmetik üründür ... ve satışlar durgunluk dönemlerinde bile dayanıklıdır.
1395
Case study
Insulation film stiffness testing
Customised engineering example
Familiar with three-point bending to test flexural strength properties?
1396
[Page extract]
BS EN ISO 4624
Describes methods for determining the adhesion by carrying out a pull-off test on a single coating or a multi-coat system of paint, varnish or related product.
1397
Page
Contact support
Thank you for contacting our support team
One of our Support Engineers or your local partner will be in touch soon.
1398
[Page extract]
Comparison with other bending methods
While the five-point bend test is designed to evaluate planar shear, other bending methods address different mechanical behaviours:
1399
Case study
Hygienic disposal bin closure testing
Customised engineering example
A manufacturer of hygienic disposal bins came to us with a nappy (diaper) disposal unit fitted with a rotary intake mechanism.
1400
[Page extract]
Comparing FCT with CMT
The flat crush test measures the compressive strength of the fluted structure in finished board, taking into account liners and adhesives.