Search results
1926
Accessory
Blank (smooth) jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 80 mm
Mec240k-B80
Blank Jaws (30mm x 80mm) - smooth steel jaw. Allows user to machine or affix own surface (eg. abrasive 'emery' paper).
Opening span = see datasheet for various spans according to the grip body selected.
Supplied as 0.5 set = 2 jaws (left…
1927
[Page extract]
Energy
Mecmesin has long been providing force and torque testing solutions to suppliers and contractors into the energy industry...
1928
[Page extract]
Equipment and safety precautions
To ensure accurate and safe testing, the following components are required:
1929
Page
Contact us about automation
Thank you for contacting our sales team about automating your testing
One of our Senior Technical Sales Engineers will reach out to you within 2 working days to discuss your requirements.
1930
[Page extract]
BS EN ISO 4624
Describes methods for determining the adhesion by carrying out a pull-off test on a single coating or a multi-coat system of paint, varnish or related product.
1931
Page
Şirket kayıtları ve politikaları
Şirket kaydı Mecmesin Limited, İngiltere ve Galler'de kayıtlı bir şirkettir. Şirket Numarası 01302639.
1932
Case study
Sentetik spor yüzey tutam bağlama
Özel mühendislik örneği Test yöntemi standardı BS ISO 4919, halıların tutam çekme kuvveti için geçerlidir.
1933
[Page extract]
ASTM D6175-03
5.1 This test method is intended to provide information on the ability of an extruded catalyst to retain physical integrity during use.
1934
Case study
Closure torque validation
Requirement
The customer had a number of Tornado closure torque testers, and wished to carry out regular validation checks without the need to return the units to either Mecmesin or an approved laboratory.
1935
[Page extract]
ISO 7886-4
This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design
1936
Test Frame
Helixa test frame
Helixa test frame
A precision motorised test frame designed to apply torque from a few mN.m right up to a capacity of 6 N.m. (50 lbf.in).Its sensitivity and axial alignment make it perfectly suited for testing fine-precision components in a quality…
1937
[Page extract]
ASTM D3039 / D3039M
ASTM D3039 determines the in-plane tensile properties of polymer matrix composite materials reinforced by high-modulus fibers. A number of calculations can be made including ultimate tensile strength, ultimate tensile strain, tensile chord modulus of
1938
[Page extract]
BS ISO 6133
BS ISO 6133 specifies five methods of calculating, after testing, the tear strength and the adhesion strength of vulcanized rubber or fabrics coated with or adhered to rubber or plastics.
1939
[Page extract]
ASTM D3410 / D3410M
ASTM D3410 determines the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.
1940
Case study
Stabilised spring testing
Customised engineering example
Our client needed to test a number of small, lightweight springs under compression. To avoid buckling and sideways movement of the springs, a supporting spindle or guide-rod was required.
1941
[Page extract]
BS ISO 7743
ISO 7743 specifies methods for the determination of the compression stress-strain properties of vulcanized or thermoplastic rubber using a standard test piece, a product or a part of a product.
Four procedures are given:
1942
Case study
Seed bottle closure torque testing
Requirement
The Royal Botanic Gardens, Kew, have undertaken an international conservation initiative to preserve seed specimens of over 24,000 plant species, protecting them from extinction at the Millennium Seed Bank at Wakehurst Place, West
1943
[Page extract]
TAPPI T 456
TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.
1944
[Page extract]
ASTM D6112-18
ASTM D6112 cover the determination of the creep and creep-rupture properties of plastic lumber and shapes, when loaded in compression or flexure under specified environmental conditions. Test specimens in the “as-manufactured” form are employed.
1945
[Page extract]
Test method and procedure
Preparing specimens
Material selection - Use representative samples from the batch being tested.
Cutting - Prepare specimens to the exact dimensions specified in
1947
[Page extract]
Comparison of relevant standards
Standard
Material types
Peel angle
Environment
1948
[Page extract]
ASTM D2731
ASTM D2731 is a test method for determining the elastic properties of elastomeric yarns made from rubber, spandex or other elastomers. Elastic properties include force at specified elongations, permanent deformation and stress decay.
1949
[Page extract]
Rheological properties and their role
Rheology, the study of deformation and flow, is central to understanding extrusion behaviour. Key properties measured include:
1950
[Page extract]
BS EN ISO 8295
ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr