Search results
1276
[Page extract]
ASTM F37-00
1.1 These test methods provide a means of evaluating the sealing properties of sheet and solid form-in-place gasket materials at room temperature.
1277
[Page extract]
Understanding peel resistance
Peel resistance is the force required to separate two bonded surfaces through a peeling motion. This force is measured using a tensile test system equipped with a peel fixture.
1278
[Page extract]
ISO 2439
The indentation hardness of flexible cellular materials is a measure of their load-bearing properties.
1279
Event
Wire Crimp & Weld Testing Webinar
The only way of really knowing the strength of a crimped terminal is to pull it.
1280
[Page extract]
Why is the trapezoidal tear test important?
Tear resistance is a critical measure of a material’s durability, particularly in applications where the material may be subject to punctures, cuts, or repeated stress.
1281
Case study
Kriket topu basınç deformasyon gücü ve kapak malzemesi çekme dayanımı
gereklilik Kookaburra, kriket ve hokey spor ekipmanları üretiminde uluslararası alanda tanınan bir liderdir. 1890 yılında kurulan şirket, inovasyon ve kaliteye gösterilen özen üzerine ismini oluşturmuştur.
1282
Product
Motorlu tork test cihazı
Girdap-dV
876-601
Vortex-dV , 10 Nm değerine sahip çok yönlü, sağlam, bağımsız bir tork test cihazıdır. Kullanımı kolay, bir üretim veya laboratuvar ortamında rutin kalite kontrol kontrolleri için uygundur. Bu motorlu standı, bir ekran ünitesine bağlı bir tork sensörü,…
1283
Test Frame
MultiTest-dV test frame
MultiTest-dV test frame
A ballscrew-driven motorised test frame designed to apply tension and compression from 2 N right up to a capacity of 2.5 kN (550 lbf).Its versatile construction makes it perfectly suited for testing all kinds of components in a…
1284
Case study
Yüksek Performanslı Plazma Kaplamalar
gereklilik Alphatek Hyperformance Coatings Ltd., birçok farklı sektöre tedarik yapan aşınma, korozyon, ısı veya elektrik dirençli kaplamalar uygulayan bir kaplama şirketidir.
1285
Sensor
Sensors - Universal Testers (ELS)
Sensors
The OmniTest universal testers use Mecmesin's range of high-resolution precision Enhanced Load Sensors (ELS) to record tensile and compressive loads.
ELSA precision loadcell connects directly to an OmniTest or MultiTest-dV stand and communicates…
1286
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
1287
[Page extract]
What is torque to turn testing?
Torque to turn testing is a method used to determine the rotational resistance in mechanical components and assemblies.
1288
[Page extract]
Analysis and interpretation of results
Interpreting shear failure characteristics
Post-test examination of the bonded joint provides valuable insight into adhesive performance:
1289
[Page extract]
What is double lap shear testing?
Double lap shear testing is a mechanical method used to measure the shear strength of adhesive bonds.
1290
[Page extract]
Types of calculations handled
Mecmesin’s VectorPro software supports a wide range of test calculations, automatically derived from mechanical testing data:
1291
[Page extract]
Speak to an expert
Selecting the right trapezoidal tear testing setup requires understanding both the material and the relevant standards.
1292
[Page extract]
Introduction to Delft tear testing
The Delft tear test is a specialised method for determining the tear strength of vulcanised rubber, thermoplastic elastomers and similar flexible materials.
1293
[Page extract]
Application of standards in puncture testing
Standardised methods ensure test consistency and reliability across laboratories and production sites.
1294
[Page extract]
ASTM and ISO approaches
ASTM D1938 specifies trouser tear testing for thin plastic films and sheeting, including specimen dimensions, pre-cu
1295
[Page extract]
FAQs about torque to turn testing
What is the difference between breakaway and running torque?
1296
[Page extract]
Speak to an Expert
Corrugated medium testing, and particularly the flat crush test under TAPPI T 809, is essential for ensuring packaging strength, reliability, and compliance.
1297
[Page extract]
Testing methods and equipment
A cleavage strength test requires precise load application and accurate force measurement at the point of separation.
1298
[Page extract]
FAQs about Young's modulus testing
What is the difference between Young’s modulus and tensile strength?
Young’s modulus measures stiffness - how much a material deforms under stress.
1299
[Page extract]
How running torque is measured
Running torque is typically measured using precision torque sensors mounted within a controlled test stand. The component under test is rotated at a defined speed, and torque is measured continuously during motion.
1300
[Page extract]
Measuring compressive modulus
Common testing methods
Internationally recognised standards specify how compressive modulus is measured for different material types and applications: