Search results
2126
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
2127
[Page extract]
Speak to a testing expert
If you're looking to validate adhesive joint performance under realistic stress conditions, our applications specialists can help configure the
2128
[Page extract]
Challenges and best practices in peel testing
Common challenges
Material variability in thickness, surface treatment, or adhesive application.
Inconsistent specimen preparation.
Operator error from misalignment or incorrect grip tension.
Best pra
2129
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
2130
[Page extract]
ASTM F607-03
The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.
2131
[Page extract]
ASTM F2132-01
This specification provides the performance requirements and associated test procedures for the puncture resistance of materials used in the construction of containers for discarded medical needles and other sharps.
2132
[Page extract]
ISO 1926
ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.
2133
[Page extract]
BS EN 2591-418
Describes a method of determining the insertion/extraction forces of female contacts used in elements of electrical and optical connection by means of gauges.
2134
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
2135
[Page extract]
BS EN 50289-3-2
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Tensile testing, Tensile strength, Elongation, Electric conductors
2136
[Page extract]
ASTM D3106
This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.
2137
[Page extract]
Step-by-step guide to conducting a CMT test
Prepare the specimen - Cut to size with clean edges, ensuring flutes remain undamaged, and condition as per the standard.
Calibrate the equipment - Check the load cell and platen alignment.
2138
Case study
รถไฟเครื่องทดสอบแรงกระแทกประตูบานเลื่อน
ความต้องการ มีการระบุอุปกรณ์พกพาสำหรับทดสอบแรงที่จำเป็นในการเปิดใช้งานอุปกรณ์ความปลอดภัยในตัวเมื่อประตูอัตโนมัติปิดบนรถไฟ จำเป็นต้องใช้งานง่ายโดยผู้ปฏิบัติงานที่ไม่ได้รับการฝึกอบรมและมีประสิทธิภาพเพียงพอสำหรับการใช้งานซ้ำ ๆ ในภาคสนาม
2139
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2140
[Page extract]
BS EN ISO 1806
This standard specifies a method of determining the mesh breaking force of netting for fishing.
2141
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
2142
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
2143
[Page extract]
BS 2782-12: 1210A to C
BS 2782-12: Method 1210A to C specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.
2144
[Page extract]
ISO 8113
ISO 8113 specifies a method for determination of the resistance of glass containers to external force in the direction of the vertical axis.
2145
[Page extract]
BS EN 12814-1
BS EN 12814-1 is a bend test method for testing welded joints of thermoplastics semi-finished products.
2146
[Page extract]
BS EN ISO 1856
BS EN ISO 1856 is a test method that specifies three methods for determining the compression set of flexible cellular materials and applies only to latex and polyurethane foams of thickness greater than 2 mm.
2147
[Page extract]
Standards for texture compression testing
ISO 16305 - Butter firmness
Specifies a method for determining butter firmness under controlled conditions.
2148
[Page extract]
ISO 8627
Specification of a test method and grading scheme for the stiffness of the tufted area of conventional manual tooth-brushes, together with the relevant information concerning definitions and those concerning testing machines.
2149
[Page extract]
SAE J 1907
This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass.
2150
[Page extract]
BS ISO 3597-2
ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.