Search results
2051
[Page extract]
ASTM D5448-11
This test method determines the inplane shear properties of wound polymer matrix composites reinforced by high-modulus continuous fibers. It describes testing of hoop wound (90°) cylinders in torsion for determination of inplane shear properties.
2052
Case study
การทดสอบปุ่มแดชบอร์ด
ความต้องการ Visteon ต้องการระบบอัตโนมัติในการวัดแรงกระตุ้นสำหรับปุ่มแดชบอร์ดและตรวจสอบจุดปิดหน้าสัมผัสไฟฟ้า ด้วยการหาจำนวนความรู้สึกส่วนตัวของปุ่มพวกเขาจะสามารถปรับปรุงความรู้สึกที่มีคุณภาพได้ เนื่องจากโหลดที่วัดได้ต่ำมากโดยทั่วไปจะน้อยกว่า 10N
2053
[Page extract]
ASTM D7233-08
This test method covers a procedure for determining the number of fractures present when paintbrush filaments are bent.
2054
[Page extract]
ASTM D3787
This test method describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation.
2055
Case study
เครื่องทดสอบแรงเลื่อนหน้าต่างรถ
ความต้องการ Bridgestone TG Adelaide ซึ่งเป็นซัพพลายเออร์รายใหญ่ของชิ้นส่วนยางให้กับอุตสาหกรรมยานยนต์ในออสเตรเลียจำเป็นต้องวัดแรงเสียดทานที่เกี่ยวข้องกับการเลื่อนหน้าต่างกระจกระหว่างไกด์ยางสองตัว
2056
[Page extract]
Why the ring crush test is critical for paperboard strength
Paperboard packaging must combine cost-efficiency with protective performance.
2057
Case study
การทดสอบสปริงอุปกรณ์ทางเดินหายใจ
ความต้องการ Bespak เป็นผู้นำด้านเครื่องมือแพทย์เฉพาะทางสำหรับการให้ยาสูดดมและการระงับความรู้สึก บริษัท ผลิตอุปกรณ์ที่ซับซ้อนมากกว่า 450 ล้านชิ้นในแต่ละปีซึ่งส่วนใหญ่เป็นเครื่องช่วยหายใจที่ใช้ในการจัดการปริมาณผงแห้งหรือยาสเปรย์ในปริมาณที่วัดได
2058
[Page extract]
BS EN 12814-4
BS EN 12814-4 is a peel test method for testing welded joints of thermoplastics semi-finished products.
2059
[Page extract]
ANSI/EIA 364-38B
This standard establishes a test method to determine the axial tensile load that can be applied to a mated pair of connectors and the holding effect of a connector cable clamp without causing any detrimental effects upon the cable or connector when subj
2060
[Page extract]
ASTM D1709-03
These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart.
2061
[Page extract]
BS EN 2747
BS EN 2747 is a tensile test method for testing carbon fibre reinforced plastics.
Before conducting BS EN 2747, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.
2062
[Page extract]
TAPPI T 400
This method describes procedures for obtaining a representative sample for testing.
2063
Case study
ความแข็งแรงในการขึ้นรูปกล่องและขอบของกล่อง
ตัวอย่างวิศวกรรมที่กำหนดเอง Box Crush Test (BCT) มักใช้เพื่อประเมินผลของการใช้แรงโหลดด้านบนตามแนวแกนกับด้านแบนของกล่องกระดาษเพื่อจำลองการเรียงซ้อนกันในคลังสินค้าหรือระหว่างการขนส่ง อย่างไรก็ตามมีการตรวจสอบเพิ่มเติมที่เรียกว่า 'การทดสอบควา
2064
[Page extract]
ISO 20344
This Standard specifies methods for testing footwear designed as personal protective equipment.
8 groups of tests from dimensions to mechanical properties and fluid resistance.
Supplemented by ISO 20345
2065
[Page extract]
ISO 6425
This document specifies requirements and test methods for divers' watches and for saturation divers' watches for use in deep diving (see Annex A which deals with watches for saturation diving).
2067
[Page extract]
BS EN 71-1
This European Standard specifies different forces or loads to be used when testing toys intended for children of different age groups.
2068
[Page extract]
BS EN ISO 7886-1
This document specifies requirements and test methods for verifying the design of empty sterile single use hypodermic syringes, with or without needle, made of plastic or other materials and intended for the aspiration and injection of fluids after fill
2069
[Page extract]
ASTM D349
These test methods cover the procedures for testing rigid round rods used in electrical insulation.
2070
[Page extract]
BS EN 12655
Gymnastics equipment, Sports equipment, Safety measures, Equipment safety, Classification systems, Dimensions, Height, Strength of materials, Stability, Mechanical testing, Vertical, Horizontal, Performance testing, Instructions for use
2071
[Page extract]
BS EN 565
Mountaineering equipment, Outdoor sports equipment, Sports equipment, Safety measures, Equipment safety, Tape, Webbing, Tensile strength, Stability, Weight measurement, Marking, Test specimens, Testing conditions
2072
[Page extract]
ISO 8364
ISO 8364:2007 specifies requirements and test methods for the binding mounting area and free space area, ski bindings and retention devices of alpine skis, in order to optimize the compatibility of the functional unit "ski binding - retention device - b
2073
[Page extract]
ASTM D3166
This test method covers the measurement of fatigue strength in shear by tension loading of adhesives on a standard specimen and under specified conditions of preparation, loading, and testing.
2074
[Page extract]
BS EN 12242
The BS EN 12242 test method is used to determine the peel strength of a touch and close (also known as “hook and loop”) fastener through a 180° peel test that is able to determine average peel and the peel strength characteristics of the product for a g
2075
[Page extract]
PD CEN/TR 17394-3
This document defines a test method for security of attachment of functional and decorative metal mechanically applied press fasteners to children's clothing including for example gloves, hats, scarves, hosiery, ties, and textile belts.