Search results
1976
[Page extract]
ASTM D1995
These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and
1977
[Page extract]
ISO 7886-4
This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design
1978
[Page extract]
ASTM C203
ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.
1979
[Page extract]
ISO 8510-1
Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test.
1980
Case study
การทดสอบการดึง Diamante
ความต้องการ ลูกค้าเป็นซัพพลายเออร์ให้กับ Marks & Spencer ผู้ค้าปลีกเสื้อผ้ารายใหญ่ในสหราชอาณาจักรซึ่งกำหนดว่าจะต้องมีการทดสอบตัวยึดและสิ่งที่แนบมาทั้งหมด
1982
[Page extract]
BS EN ISO 8670-2
Two part test on filled bags:
1) 20 N tensile flange seal test, pulled in two directions in turn, at 180 degrees, in shear plane across flange, bag held by transparent custom plate
1983
[Page extract]
ISO 594-2
ISO 594 and EN 1707 contain 8 separate tests, some of which are only applicable to Luer lock fittings. Most of these tests require that the sample be assembled to a particular precision steel reference fitting.
1984
[Page extract]
PSTC 8
Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape.
The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.
1985
[Page extract]
ASTM D7137 / D7137M-17
ASTM D7137 is a test method that measures the compression residual strength properties of multidirectional polymer matrix composite laminated plates, which have been subjected to quasi-static indentation
1986
[Page extract]
BS EN ISO 11608-3
Medical equipment, Medical instruments, Parenteral infusion equipment, Injection instruments, Injection guns, Syringes, Drug administration, Measuring cylinders, Containers, Performance testing, Performance, Leak tests, Design, Dimensions
1987
[Page extract]
ASTM D2979
This test method covers measurement of the pressure-sensitive tack of adhesives.
1988
Case study
การทดสอบการดึงโบว์ติดเสื้อผ้า
ความต้องการ ลูกค้าเป็นซัพพลายเออร์ให้กับ Marks & Spencer ผู้ค้าปลีกเสื้อผ้ารายใหญ่ในสหราชอาณาจักรซึ่งกำหนดว่าต้องทดสอบตัวยึดและสิ่งที่แนบมาทั้งหมดว่าล้มเหลว
1989
[Page extract]
ISO 813
ISO 813 specifies a method for the determination of the adhesive strength of a vulcanized or thermoplastic rubber bonded to a rigid substrate, using a test piece comprising a strip of rubber bonded to a single plate of rigid material.
1990
[Page extract]
ASTM D1871
This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.
1991
[Page extract]
ASTM D5169-98
This test method measures the shear strength of hook and loop touch fasteners using a recording constant rate of extension (CRE) tensile testing machine.
1992
[Page extract]
BS EN 520
Plasterboard, Gypsum plaster, Boards, Wall linings, Construction systems parts, Performance, Strength of materials, Fire resistance, Sound insulation, Water vapour, Permeability, Thermal resistance, Performance testing, Dimensional measurement, Physical
1993
[Page extract]
ASTM D380
ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.
1994
[Page extract]
ASTM D2659
ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.
1995
[Page extract]
BS EN ISO 10619-1
BS EN ISO 10619-1 is a test method covering bending tests on rubber or plastics hoses and tubing.
1997
Specials
Thermal cabinet environment chamber
Environmental chamber capability
Mecmesin's OmniTest twin column range can accommodate an environmental chamber to test materials in controlled ambient conditions.
1998
[Page extract]
ASTM D3410 / D3410M
ASTM D3410 determines the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.
1999
[Page extract]
BS EN 1464
Specifies a floating roller method for the determination of the peel resistance of adhesive bonds between one rigid adherend and one flexible adherend when tested under specified conditions of preparation and testing.
2000
[Page extract]
IEC 61196-1-308
IEC 61196-1-308:2012(E) applies to coaxial communication cables. It specifies test methods for tensile strength and percentage elongation at fracture for annealed and hard-drawn solid copper clad metals to be used as inner conductor for coaxial cables.