Search results
2101
Case study
การทดสอบสปริงที่เสถียร
ตัวอย่างวิศวกรรมที่กำหนดเอง ลูกค้าของเราจำเป็นต้องทดสอบสปริงขนาดเล็กน้ำหนักเบาจำนวนหนึ่งภายใต้การบีบอัด เพื่อหลีกเลี่ยงการโก่งงอและการเคลื่อนตัวไปด้านข้างของสปริงจำเป็นต้องใช้แกนรองรับหรือแกนนำ
2102
[Page extract]
BS EN ISO 205
Adhesives. Wood adhesives for non-structural applications. Determination of tensile shear strength of lap joints.
2103
[Page extract]
BS EN 1895
Adhesives, Adhesion tests, Peeling tests, Paper, Paper products, Board (paper), Disposable, Packaging materials, Flexible materials
2104
[Page extract]
ASTM D4533-11
This test method is an index test used to measure the force required to continue or propagate a tear in woven or non-woven geotextiles by the trapezoid method.
2105
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
2106
[Page extract]
Interpreting test results
Peel strength is typically reported in newtons per metre (N/m) or per 25 mm of bond width (N/25mm), depending on the industry standard. From the force-displacement graph, the following characteristics are analysed:
2107
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
2108
Event
Advanced Engineering 2021 - We would love to see you there!
Who should attend?
Engineering professionals and managers from advanced manufacturing sectors interested in quality assurance testing solutions.
What is the exhibition about?
2109
[Page extract]
BS EN 12467
Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio
2110
Case study
รถไฟเครื่องทดสอบแรงกระแทกประตูบานเลื่อน
ความต้องการ มีการระบุอุปกรณ์พกพาสำหรับทดสอบแรงที่จำเป็นในการเปิดใช้งานอุปกรณ์ความปลอดภัยในตัวเมื่อประตูอัตโนมัติปิดบนรถไฟ จำเป็นต้องใช้งานง่ายโดยผู้ปฏิบัติงานที่ไม่ได้รับการฝึกอบรมและมีประสิทธิภาพเพียงพอสำหรับการใช้งานซ้ำ ๆ ในภาคสนาม
2111
[Page extract]
Advances in adhesive testing
Modern systems incorporate high-resolution digital sensors for precise force measurement, real-time data capture with analytical software, and automation to reduce operator influence.
2112
[Page extract]
Consumer Products
Mecmesin test solutions for products typically found in the home ...
2113
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2114
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
2115
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
2116
[Page extract]
ASTM D3106
This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.
2117
Case study
การทดสอบ TTF แบบดึงปุ่มเสื้อผ้า
ความต้องการ ลูกค้าเป็นซัพพลายเออร์ให้กับ Marks & Spencer ผู้ค้าปลีกเสื้อผ้ารายใหญ่ในสหราชอาณาจักรซึ่งกำหนดว่าต้องทดสอบตัวยึดและสิ่งที่แนบมาทั้งหมดว่าล้มเหลว
2118
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
2119
Case study
กดการทดสอบการดึงออกของแกนป๊อปเปอร์
ความต้องการ ลูกค้าเป็นซัพพลายเออร์ให้กับร้านค้าปลีกเสื้อผ้ารายใหญ่ Marks & Spencer ซึ่งกำหนดว่าต้องทดสอบตัวยึดและสิ่งที่แนบมาทั้งหมดว่าล้มเหลว
2120
[Page extract]
BS 2782-3: 360C
BS 2782-3: Method 360C specifies a test method for testing the tear resistance of plastics film and sheeting by the initiation method
2121
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
2122
[Page extract]
BS EN 12814-2
BS EN 12814-2 is a tensile test method for testing welded joints of thermoplastics semi-finished products.
2123
[Page extract]
Speak to a testing expert
If you're looking to validate adhesive joint performance under realistic stress conditions, our applications specialists can help configure the
2124
[Page extract]
ASTM D6195-03
These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.