Search results
1201
[Page extract]
Comparing adhesion test methods
While the peel wheel test maintains a constant 90° angle, other tests such as the 180° peel test are also widely used.
1202
[Page extract]
Why is texture testing important?
Texture testing ensures consistent product performance, supports process control, and validates compliance with industry standards. Even small changes in raw materials, processing conditions, or environmental factors can alter texture.
1203
[Page extract]
Tension testing process
Tension testing is the most common method for evaluating tensile deformation and produces quantitative data on how materials behave under controlled pulling forces.
1204
[Page extract]
Application in food texture analysis
Tension methods replicate real-world conditions experienced by food products during production, handling, and consumption.
1205
[Page extract]
Understanding peel resistance
Peel resistance is the force required to separate two bonded surfaces through a peeling motion. This force is measured using a tensile test system equipped with a peel fixture.
1206
[Page extract]
How bridge torque is measured
Bridge torque is measured by applying rotational force to a closure until the tamper-evident bridges shear.
1207
[Page extract]
Overview of TerraFixing
TerraFixing is dedicated to combating climate change through affordable and scalable Direct Air Carbon Capture (DAC).
1208
[Page extract]
Introduction to single rip trouser tear testing
Single rip trouser tear testing is a method used to measure a material’s ability to resist the propagation of a tear once it has started.
1209
[Page extract]
Compression testing standards
Following recognised standards ensures test data is reliable and comparable. Standards specify specimen preparation, testing speeds, calculations and reporting methods.
1210
[Page extract]
Why choose Mecmesin torque testing equipment
From manual testers to automated systems
Mecmesin offers a wide range of torque testing solutions suitable for R&D, quality assurance, and full-scale production.
1211
[Page extract]
Methods of compressive burst testing
Inflationary burst testing
In this method, internal pressure is gradually increased using air, gas, or liquid until the container ruptures. This is widely applied to:
1212
[Page extract]
Food & Drink
Mecmesin solutions for the food and drink sector.
We live in a world where the majority of food and drink products are supplied pre-packed in packaging that protects, but that is designed to be opened easily.
1213
Event
Mechanical Performance Testing of Medical Devices Webinar
A hands-on Force and Torque how-to demonstration event.
1214
[Page extract]
BS EN 1608
This European Standard specifies the equipment and procedures for determining the tensile strength of a product parallel to its faces. It is applicable to thermal insulating products.
1215
[Page extract]
ASTM D1876
This test method measures the peel separation strength of two flexible materials that have been bonded together.
1216
[Page extract]
ISO 11897
ISO 11897 specifies a method for the determination, under given conditions, of the resistance to tear propagation on an edge fold of sacks made from thermoplastic flexible film.
1217
[Page extract]
ASTM D1321
This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.
1218
Event
Fundamentals of Compression Testing
Push or compressive testing helps determine the limits of most products that require constant pushing or compression.
1219
[Page extract]
IEC 62137-1-1
The test method described in IEC 62137-1-1:2007 is applicable to gull-wing lead surface mounting components.
1220
[Page extract]
ASTM F2458-05
This test method covers a means for comparison of wound closure strength of tissue adhesives used to help secure the apposition of soft tissue.
1221
[Page extract]
IEC 61210
IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and a mating female connector for use as either an incorporated or an integrated part o
1222
[Page extract]
BS ISO 3597-2
ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.
1223
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
1224
[Page extract]
ASTM D6958-03
These test methods describe an evaluation procedure for the determination of undesirable side-bonding of coatings for wood flooring.
1225
Event
WestPack Expo 2025
Lansmont - together with our sister brand Mecmesin - will be participating in the upcoming WestPack trade show!