Search results
2651
[Page extract]
BS EN 862
Packaging. Child resistant packaging. Requirements and testing procedures for non-reclosable packages for non-pharmaceutical products
2653
[Page extract]
ASTM C1576
This standard test method covers the determination of slow crack growth (SCG) parameters of advanced ceramics by using constant stress flexural testing in which time to failure of flexure test specimens is determined in four-point flexure as a function
2654
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
2656
[Page extract]
ISO 10354
Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.
2657
[Page extract]
ISO 814
ISO 814 specifies a method for determining the adhesion strength of rubber-to-metal bonds where the rubber part is assembled between two parallel metal plates, using the adhesive system under investigation
2658
Product
เครื่องทดสอบแรงยึดเกาะที่สมบูรณ์แบบ
เครื่องทดสอบแรงดึงหน้า
802-001+853-415
เครื่องทดสอบการดึงหน้าของ Mecmesin ใช้ใน เครื่องผูก กว่า 100 เครื่องทั่วโลก มันให้วิธีการที่แข็งแกร่งประหยัดและทำซ้ำได้ในการวัดความแรงดึงหน้าของหนังสือที่สมบูรณ์แบบ ด้วยการเปิดใช้งานการ ทดสอบความทนทานต่อการผูกมัดที่ มีประสิทธิภาพเครื่อง ทดสอบ…
2659
Case study
การทดสอบเข็มฉีดยาตามมาตรฐาน ISO 11040-4 ภาคผนวก F: การทดสอบการเจาะเข็มและการลาก
สำรวจคู่มือที่ครอบคลุมนี้เกี่ยวกับการทดสอบเข็มฉีดยาตามมาตรฐาน ISO 11040-4 ภาคผนวก F เรียนรู้กระบวนการทีละขั้นตอนของการทดสอบการเจาะเข็มและการลาก อุปกรณ์ที่จำเป็น และแนวทางปฏิบัติที่ดีที่สุดเพื่อให้ได้ผลลัพธ์ที่แม่นยำ
2660
[Page extract]
ASTM E328-02
These test methods cover the determination of the time dependence of stress (stress relaxation) in materials and structures under conditions of approximately constant constraint, constant environment, and negligible vibration.
2661
[Page extract]
ASTM D1871
This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.
2662
[Page extract]
ASTM D4027-98
This test method describes equipment and procedures to measure the shear modulus and shear strength of adhesive layers between rigid adherends.
2663
[Page extract]
ASTM D3039 / D3039M
ASTM D3039 determines the in-plane tensile properties of polymer matrix composite materials reinforced by high-modulus fibers. A number of calculations can be made including ultimate tensile strength, ultimate tensile strain, tensile chord modulus of
2664
[Page extract]
USP <381>
This chapter applies to closures used for long-term storage of preparations defined in the general test chapter Packaging and Storage Requirements á659ñ, Injection Packaging.
2665
[Page extract]
BS EN ISO 10066
BS EN ISO 10066 is a test method for determining creep in tension of flexible cellular polymeric materials.
2666
[Page extract]
Special compression fixtures
Special compression fixtures have been specially designed to meet the challenges of a particular application.
2669
[Page extract]
EN 14488-2
Part 1: Sampling fresh and hardened concrete
Part 2: Compressive strength of young sprayed concrete
Part 3: Flexural strengths (first peak, ultimate and residual) of fibre reinforced beam specimens
2671
[Page extract]
IFI 143
This standard provides a test method for determining the torque-tension relationship on both external and internal threaded fasteners for the purpose of measuring the frictional characteristics of the threaded fasteners.
2672
[Page extract]
BS EN 2243-2
This standard defines the general requirements for the determination of strength of structural adhesives by testing in peel metal to metal joints, at ambient or other temperatures.
2673
[Page extract]
BS EN 2591-417
Defines a method of determining the tensile strength of crimped connections used in elements of electrical and optical connection.
2675
[Page extract]
BS EN 3841-509
This standard specifies a method of determining the forces required to insert and extract the contact pin into and out of the terminal socket of the signal contact. It shall be used together with EN 3841-100.