Search results
1651
[Page extract]
Ultimate Tensile Strength Formula - How to Calculate UTS
The formula to calculate ultimate tensile strength is:
Where:
1652
[Page extract]
Mecmesin solutions for compressive hardness testing
Mecmesin designs and supplies precision testing systems for compressive hardness applications across industries.
1653
[Page extract]
Mecmesin solutions for rotational shear testing
Mecmesin provides torque testing systems designed for high-precision, repeatable results in rotational shear testing.
1654
[Page extract]
Equipment for loop tack testing
Mecmesin loop tack testers are designed for precision, repeatability, and compliance with industry standards.
1655
[Page extract]
How these calculations are applied
These values are calculated instantly as part of the test routine. Predefined formulas and logic conditions are applied to the captured data, delivering results in real time.
Applications include:
1656
Sensor
Sensors - Helixa
Torque sensors
The HTC range of interchangeable torque sensors are specially adapted for the Helixa test system. Plug and play for automatic calibration with availability to suit all requirements in capacities from 0.1 N.m (0.9 lbf.in) to 6 N.m (50 lbf.in…
1657
[Page extract]
IEC 62137-1-1
The test method described in IEC 62137-1-1:2007 is applicable to gull-wing lead surface mounting components.
1658
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
1659
[Page extract]
ISO 10354
Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.
1660
[Page extract]
ISO 7886-2
This document specifies requirements for sterile single-use hypodermic syringes of nominal capacity 1 ml and above, made of plastic materials and intended for use with power-driven syringe pumps. Annexe B covers the Pump Force to be measured.
1661
[Page extract]
ASTM D1321
This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.
1662
[Page extract]
ISO 8033
ISO 8033 specifies methods for the determination of the adhesion between lining and reinforcement, between cover and reinforcement, between reinforcement layers, between cover and outer lamination (thin layer of material outside the cover for protection
1663
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
1664
[Page extract]
Torque systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers? Do you want to reduce testing time and increase throughput for operators when performing batch tests?
1665
[Page extract]
ASTM D412-16
ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.
1666
Test Frame
Helixa test frame
Helixa test frame
A precision motorised test frame designed to apply torque from a few mN.m right up to a capacity of 6 N.m. (50 lbf.in).Its sensitivity and axial alignment make it perfectly suited for testing fine-precision components in a quality…
1667
[Page extract]
ASTM F2332-06
This specification covers annular ball bearings intended primarily for use in instrument and precision rotating components.
1668
[Page extract]
BS EN 13411-3
This European Standard deals with the requirements for ferrules for the ferrule-securing of eyes and endless loops - it applies to slings and assemblies using steel wire ropes for general lifting applications up to and including 60mm diameter conforming
1669
[Page extract]
ASTM D6272-17
This test method covers the determination of flexural properties of unreinforced and reinforced plastics, including high-modulus composites and electrical insulating materials in the form of rectangular bars molded directly or cut from sheets, plates, o
1670
[Page extract]
ASTM D3846
ASTM D3486 is a test method used for evaluating the in-plane strength of reinforced thermosetting plastics in flat sheet form in thicknesses ranging from 2.54 to 6.60 mm.
1671
[Page extract]
IEC 61196-1-308
IEC 61196-1-308:2012(E) applies to coaxial communication cables. It specifies test methods for tensile strength and percentage elongation at fracture for annealed and hard-drawn solid copper clad metals to be used as inner conductor for coaxial cables.
1672
[Page extract]
Standards for the peel wheel test
Standardisation ensures peel wheel tests are consistent and repeatable across laboratories and production sites.
1673
[Page extract]
ASTM D3577
1. Scope ... 1.1 This specification describes certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.
1674
Page
Accessory catalogue
Choosing your accessories
To achieve accurate test results it's important that your sample is gripped and held correctly.