Search results
2076
[Page extract]
Comparative analysis of testing standards
Different standards address specific materials and applications:
2077
[Page extract]
CCT compared to ECT and FCT
CCT - Material-level test, used to assess raw medium quality before conversion into board
2078
[Page extract]
Step-by-step guide to conducting a CMT test
Prepare the specimen - Cut to size with clean edges, ensuring flutes remain undamaged, and condition as per the standard.
Calibrate the equipment - Check the load cell and platen alignment.
2079
[Page extract]
Speak to an expert
Top-load testing provides a vital measure of packaging performance, helping engineers and quality teams optimise designs, comply with regulations and ensure product safety.
2080
[Page extract]
Applications in industry
The Delft tear test is used wherever rubber and thermoplastics need to maintain performance under stress. Common uses include:
2081
[Page extract]
Speak to an expert
Compression texture testing is essential for ensuring food products are consistent, compliant, and satisfying to consumers.
2082
[Page extract]
Speak to an expert
If you require loop tack testing to meet quality, performance, or compliance requirements, Mecmesin can provide the right solution for your application.
2083
[Page extract]
Applications of floating roller peel testing
Floating roller peel testing is employed to verify both material selection and process stability in various high-performance sectors:
2084
[Page extract]
Speak to an expert
The climbing drum peel test is a critical method for evaluating adhesive bond strength where performance and safety cannot be compromised.
2085
[Page extract]
Applications and benefits of shear testing
Shear testing is used across a wide range of food products, including meats, dairy products, plant-based foods,
2086
[Page extract]
Key applications of pull-off and pull-out testing
The versatility of these tests means they are used across a broad range of products and industries.
2087
[Page extract]
Comparing adhesion test methods
While the peel wheel test maintains a constant 90° angle, other tests such as the 180° peel test are also widely used.
2088
[Page extract]
Interpreting compressive strength test results
Interpreting results involves more than noting the peak load. Stress–strain curves reveal additional information such as modulus, yield point, and failure mode.
2089
[Page extract]
Interpreting trapezoidal tear test results
Test results typically report peak tear force in newtons, and sometimes the average force during propagation. Engineers use this data to:
2090
[Page extract]
Case studies
Luer connector testing
A medical device manufacturer needed to verify strip torque for Luer connectors used in IV systems.
2091
[Page extract]
Common challenges and solutions
Torque testing can be influenced by several factors:
2092
[Page extract]
Key mechanical testing methods
Short span compression testing differs from conventional compression tests because it uses a minimal support length to eliminate bending effects.
2093
[Page extract]
Standards in torque testing
Mecmesin systems are designed to comply with widely recognised international standards.
2094
[Page extract]
Interpreting test results
Peel strength is typically reported in newtons per metre (N/m) or per 25 mm of bond width (N/25mm), depending on the industry standard. From the force-displacement graph, the following characteristics are analysed:
2095
[Page extract]
Introduction to tear testing
Tear testing is a quality control procedure used to measure the resistance of a material to tearing under controlled conditions.
2096
[Page extract]
Benefits of regular ergonomic testing
Routine testing offers measurable benefits for employers, healthcare providers, and safety professionals:
2097
[Page extract]
Speak to an expert
Compressibility and recovery testing is essential for verifying material performance in sealing, cushioning, and structural applications.
2098
[Page extract]
Introduction to pull-off and pull-out testing
Pull-off and pull-out testing are widely used to measure the strength, durability, and reliability of materials, adhesives, coatings, and mechanical fixings.
2099
[Page extract]
Speak to an Expert
For expert guidance on fastening torque testing, Mecmesin’s technical specialists can help you select the right tester, develop compliant test methods, and optimise fixture design for you
2100
[Page extract]
Key properties measured in tensile testing
While ultimate tensile strength is the headline result, tensile testing also measures: