Search results
126
[Page extract]
BS EN 12814-2
BS EN 12814-2 is a tensile test method for testing welded joints of thermoplastics semi-finished products.
127
[Page extract]
BS EN 2597
BS EN 2597 is test method covering tensile testing on carbon fibre reinforced plastics.
Before conducting BS EN 2597, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.
128
[Page extract]
BS ISO 11752
BS ISO 11752 is a test method for determining the compressibility of flexible cellular polymeric materials.
129
[Page extract]
BS EN ISO 6892-2
BS EN ISO 6892-2 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature.
130
[Page extract]
ASTM D3916
ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.
131
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
132
[Page extract]
ASTM D3518 / D3518M
ASTM D3518 is a test method, which measure the shear stress and shear strain properties of polymer matrix composite materials composed of +45 plies and -45° plies.
133
[Page extract]
ASTM d6108-19
ASTM D6108 covers the determination of the mechanical properties of plastic lumber and shapes, when the entire cross-section is loaded in compression at relatively low uniform rates of straining or loading.
134
[Page extract]
ASTM D3330
These test methods cover the measurement of the peel adhesion of single and double-sided pressure-sensitive tapes.
135
[Page extract]
ASTM D695-15
ASTM D695 is a test method used to determine the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading.
136
[Page extract]
BS EN ISO 527-1
BS EN ISO 527-1 specifies the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.
137
[Page extract]
ASTM F1304-18
ASTM F1304 is a test method used to determine the deflection of relatively rigid resilient floor tile such as vinyl composition tile and resilient flooring with a rigid polymeric core.
138
[Page extract]
ASTM D1623
ASTM D1623 determines the tensile and tensile adhesion properties of rigid cellular plastics materials and foam. These are often used as insulation and structural materials in the aerospace, automotive and construction industries.
139
[Page extract]
ASTM D413-98
ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.
140
[Page extract]
ASTM D2979
This test method covers measurement of the pressure-sensitive tack of adhesives.
141
[Page extract]
TAPPI T 456
TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.
142
[Page extract]
ASTM C582
This specification covers composition, thickness, fabricating procedures, and physical property requirements for glass fiber reinforced thermoset polyester, vinyl ester, or other qualified thermosetting resin laminates comprising the materials of constr
143
[Page extract]
BS EN ISO 8295
ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr
144
[Page extract]
ASTM D2653
ASTM D2653 determines the tensile properties of elastomeric yarns made from natural rubber, spandex or other elastomers.
145
[Page extract]
BS EN 681-1
This standard specifies requirements for materials used in vulcanized rubber seals for:
1) cold potable water supply (up to 50®C);
146
[Page extract]
ASTM D3826
ASTM D3826 is a tensile test method, which covers a degradation-end point, or a brittle point) for degradable polyethylene/polypropylene films and sheeting less than 1.0 mm thick.
147
[Page extract]
ASTM F152-95
ASTM F152 is a test standard that covers tensile strength of nonmetallic gasketing materials at room temperature.
148
[Page extract]
ASTM F1306
ASTM F1306, is a test method, which permits flexible barrier films and laminates to be characterised for slow rate penetration resistance to a driven probe.
149
[Page extract]
ISO 178
ISO 178 is a test method for the determination of flexural properties of rigid and semi-rigid plastics. These properties include flexural modulus and flexural strength.