Search results
1901
[Page extract]
Introduction to edge crush testing (ECT)
The edge crush test (ECT) is a standard method used to evaluate the edgewise compressive strength of corrugated fibreboard.
1902
[Page extract]
Key methods in shear stress measurement
There are several approaches to measuring shear stress, with rotational shear testing and torsion-based techniques among the most widely used.
1903
[Page extract]
Equipment and techniques
Accurate T-peel testing requires precise, calibrated instruments.
1904
[Page extract]
Three-point vs four-point bend testing
In a three-point bend test, force is applied at a single midpoint. In a four-point bend test, two loading noses distribute the load over a larger section of the specimen.
1905
[Page extract]
Choosing the right tear testing equipment
Selecting the correct tear tester depends on the type of material, accuracy requirements, testing volume, and available budget.
Factors to consider:
1906
[Page extract]
Take control of your torque testing
Torque testing is a way of determining how an object will react when it is being turned - during normal operation or being twisted until it deliberately fails or breaks.
1907
[Page extract]
Case studies - real-world applications
Medical vial stoppers
A pharmaceutical company tested rubber vial stoppers to ASTM F2132 to ensure they resisted accidental puncture during handling.
1908
[Page extract]
Applications of short span compression testing
SCT is widely applied in quality assurance, R&D, and material qualification:
1909
[Page extract]
Standards and compliance
Commonly referenced standards for tangent modulus testing include:
1910
[Page extract]
ECT vs BCT
While ECT measures the compressive strength of the board material, the box compression test (BCT) measures the strength
1911
[Page extract]
Introduction to torque testing
Torque testing is a vital part of packaging quality control.
1912
[Page extract]
Applications of bursting strength testing
Ball burst testing is routinely used across sectors where material failure under localised stress poses a risk to performance or safety. Common application areas include:
1913
[Page extract]
Interpreting results and ensuring accuracy
Accurate results rely on correct setup and consistent procedures:
1914
[Page extract]
Adapting to new materials
As new materials such as bio-based films, nanocomposites, and high-performance fibres emerge, testing methods must adapt.
1915
[Page extract]
FAQs
Find answers to common questions about syringe testing and ISO 11040-4:
1916
[Page extract]
What is Ultimate Tensile Strength in Materials Testing?
Ultimate tensile strength (UTS) refers to the maximum stress a material can endure while being stretched before it fails.
1917
[Page extract]
Comparative analysis of testing standards
Different standards address specific materials and applications:
1918
[Page extract]
VectorPro's key features
Design
Intuitive icon-driven interface and workspace
Advanced 'drag and drop' test routine builder
Personalised u
1919
[Page extract]
Step-by-step guide to conducting a CMT test
Prepare the specimen - Cut to size with clean edges, ensuring flutes remain undamaged, and condition as per the standard.
Calibrate the equipment - Check the load cell and platen alignment.
1920
[Page extract]
What is the trapezoidal tear test?
The trapezoidal tear test is a mechanical method used to determine the tear strength of flexible sheet materials.
1921
[Page extract]
Applications in industry
The Delft tear test is used wherever rubber and thermoplastics need to maintain performance under stress. Common uses include:
1922
[Page extract]
Speak to an expert
If you require loop tack testing to meet quality, performance, or compliance requirements, Mecmesin can provide the right solution for your application.
1923
[Page extract]
Introduction to four-point bend testing
Four-point bend testing is a fundamental method in materials science, providing engineers and quality assurance professionals with a reliable way to assess the
1924
[Page extract]
What’s their secret?
“Prior to joining our class, most of our students had no actual experience with materials testing, apart from what they saw in a textbook.
1925
Event
Introduction to consumer packaging testing
In the competitive world of consumer goods, damaged packaging isn't just a financial setback—it can tarnish your brand's reputation.