Search results
176
Accessory
1/2" upper chuck assembly for use on Helixa sensors (3 N.m & 6 N.m only)
432-617
A standard self-centering 3-jaw chuck with key.
It has a maximum ½" (12.7 mm) opening and is connected to the Helixa torque sensor via an adaptor with female ⅜" square hole.
Used to secure a variety of test specimens for torque applications of 1.5 - 10…
177
Accessory
Self-levelling Compression Plate Steel - 96 mm, 25 kN, QC-20 fitting
MecS223k-96
MecS223k - 96mm diameter:
Self-levelling allows exact parallelism to be set between the upper and lower plates.. ideal for those applications where it is critical to accurately measure the deformation of a sample.
The MecS223 range of hardened steel…
178
Accessory
Charger for digital gauges, UK, 230 V, 3-pin square
304-005
For use with Mecmesin digital force and torque gauges. 230 Volt with 3 square pins. Commonly used in the UK.
The mains adaptor/charger is a constant-current type:
Primary circuit: 230V – 50Hz
Secondary circuit: 100mA constant current at 9V Charger…
179
Accessory
Self-levelling Compression Plate Steel - 196 mm, 25 kN, QC-20 fitting
MecS223k-196
MecS223k - 196mm diameter:
Self-levelling allows exact parallelism to be set between the upper and lower plates.. ideal for those applications where it is critical to accurately measure the deformation of a sample.
The MecS223 range of hardened steel…
180
Accessory
Mitutoyo DP-1VA Series 264-Digimatic Mini-Processor (Euro)
432-205
A palm-sized printer manufactured by Mitutoyo. It is used to print measurement data from the digimatic signal of digital force and torque instruments.
Performs statistical analysis and can draw a histogram or D chart in addition to more complicated…
181
Accessory
Mounting plate for QC-20 Male Post on 50 kN systems
432-622
Allows QC type C Adapter (20mm Male Post) to be fitted directly to the base of 50 kN test systems.
Used when QC-20 grips and fixtures are in long-term use on 50kN test stand.
Supplied with 6 screws of M6 thread.
182
Accessory
Lower Keyless Chuck, large, round shaft, fits Vortex spindle
432-445
Lower ‘keyless’ 4-jaw Chuck (large)
Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 80mm depending on jaws selected.
Used for holding…
183
Accessory
1/2" Lower Chuck Assembly for use on Helixa motor spindle
432-616
A standard self-centering 3-jaw chuck with key. It has a maximum ½ " (12.7 mm) opening and is connected to the Helixa motor-drive spindle via an adaptor with quick-release grub-screw. Used to secure a variety of test specimens for torque applications of 1…
184
Accessory
Self-levelling Compression Plate Steel - 56 mm, 25 kN, QC-20 fitting
MecS223k-56
MecS223k - 56mm diameter:
Self-levelling allows exact parallelism to be set between the upper and lower plates.. ideal for those applications where it is critical to accurately measure the deformation of a sample.
The MecS223 range of hardened steel…
185
Accessory
Charger for digital gauges, Europe, 230 V, 2-pin round
304-004
For use with Mecmesin digital force and torque gauges. 220 Volt with 2 round pins. Commonly used in Europe, South America and Asia.
The mains adaptor/charger is a constant-current type:
Primary circuit: 230V – 50Hz
Secondary circuit: 100mA constant…
186
Accessory
Self-levelling Compression Plate Steel - 156 mm, 25 kN, QC-20 fitting
MecS223k-156
MecS223k - 156mm diameter:
Self-levelling allows exact parallelism to be set between the upper and lower plates.. ideal for those applications where it is critical to accurately measure the deformation of a sample.
The MecS223 range of hardened steel…
187
Accessory
Mitutoyo DP1-VA Series 264-Digimatic Mini-Processor (UK)
432-204
A palm-sized printer manufactured by Mitutoyo. It is used to print measurement data from the digimatic signal of digital force and torque instruments.
Performs statistical analysis and can draw a histogram or D chart in addition to more complicated…
188
Accessory
3/8" Upper Chuck Assembly for use on Helixa sensors
432-615
A standard self-centering 3-jaw chuck with key.
It has a maximum ⅜" (9.5 mm) opening and is connected to the Helixa torque sensor via an adaptor with female ⅜" square hole.
Used to secure a variety of test specimens for torque applications of 1.5 - 10…
189
Accessory
FINAT 2 Assisted Pull-Peel Table, 90 degrees, adjustable rails for float glass, QC-20
PDV15031
The FINAT 2 Assisted Pull-Peel table (90° Peel Test) is fitted to the anvil plate of a motorised test stand and then connected to the crosshead of a test stand. It is commonly used for conducting peel tests on adhesive tapes and films.
The carriage of…
190
Accessory
Self-levelling Compression Plate Steel - 156 mm, 25 kN, QC-20 fitting
MecS223k-156
MecS223k - 156mm diameter:
Self-levelling allows exact parallelism to be set between the upper and lower plates.. ideal for those applications where it is critical to accurately measure the deformation of a sample.
The MecS223 range of hardened steel…
191
Accessory
Charger for touchscreen digital gauges, USA, USB-A, USB-C, 2-pin flat
304-072
For use with Mecmesin touchscreen digital force and torque gauges. With 2 flat pins. Commonly used in the USA.
The mains adaptor/charger is a USB-A, USB-C type:
Input: 100-240V~50/60Hz 0.5A
Output-C: 5.0V=3.0A; 9.0V=2.22A; 12.0V=1.5A
Output-A: 3.6-6.…
192
Accessory
Small Pinch Grip, 200 N, 10-32 UNF
432-280
Pinch grips are lightweight miniature vice grips, which use a hinge action to clamp a sample and a wing nut to tighten the jaw face.
Each 10 mm x 10 mm jaw face has a slight groove to help to hold the sample securely, yet avoid inducing a break within…
193
Accessory
Self-levelling Compression Plate Steel - 116 mm, 25 kN, QC-20 fitting
MecS223k-116
MecS223k - 116mm diameter Self-levelling Compression Plate:
Self-levelling allows exact parallelism to be set between the upper and lower plates.. ideal for those applications where it is critical to accurately measure the deformation of a sample.
The…
194
Accessory
Small Parallel Grip, 500 N, 10-32 UNF
432-394
Small Parallel Grips are designed for tensile testing of small flat components and materials below 500N.
A floating ball screw attachment ensures central loading during tensile testing and wing screws are used to quickly position the jaws.
Jaw faces…
195
Accessory
3/8" Lower Chuck Assembly for use on Helixa motor spindle
432-614
A standard self-centering 3-jaw chuck with key.
It has a maximum ⅜" (9.5mm) opening and is connected to the Helixa motor-drive spindle via an adaptor with quick-release grub-screw.
Used to secure a variety of test specimens for torque applications.
196
Accessory
FINAT 1 Peel Jig for 180 degree testing, QC-20
PDV13016-C
FINAT 1 Peel Jig - 180°
A polished steel plate used for affixing pressure-sensitive adhesive tape in accordance with FINAT 1 test method and other international standards.
Fitted with an adaptor having QC-20mm female hole for connection to the base of…
197
Accessory
Self-levelling Compression Plate Steel - 116 mm, 25 kN, QC-20 fitting
MecS223k-116
MecS223k - 116mm diameter Self-levelling Compression Plate:
Self-levelling allows exact parallelism to be set between the upper and lower plates.. ideal for those applications where it is critical to accurately measure the deformation of a sample.
The…
198
Accessory
FINAT 2 Assisted Pull-Peel Table, 90 degrees, adjustable rails for float glass, QC-20
PDV15031
The FINAT 2 Assisted Pull-Peel table (90° Peel Test) is fitted to the anvil plate of a motorised test stand and then connected to the crosshead of a test stand. It is commonly used for conducting peel tests on adhesive tapes and films.
The carriage of…
199
Accessory
Automated Syringe Batch Tester
PDV19179
The Automated Syringe Batch tester is a bench-top system for checking the ‘break-loose’ and ‘glide force’ of up to 12 individual syringes in one ‘load-and-run’ cycle. In the face of increased demand on production of syringes, this system enables larger…
200
Accessory
Charger for touchscreen digital gauges, Europe, USB-A, USB-C, 2-pin round
304-067
For use with Mecmesin touchscreen digital force and torque gauges. With 2 round pins. Commonly used in the Europe.
The mains adaptor/charger is a USB-A or USB-C type:
Input: 100-240V~50/60Hz 0.5A
Output-C: 5.0V=3.0A; 9.0V=2.22A; 12.0V=1.5A
Output-A: 3…