Search results
1076
[Page extract]
PSTC 8
Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape.
The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.
1077
[Page extract]
ASTM D429-14
ASTM D429 is a test method used to determine the adhesion of rubber to metal substrates. It comprises 8 different tests: A through to H, covering tensile strength, peel and shear strength of the adhesion interface.
1078
[Page extract]
ASTM D3787
This test method describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation.
1079
Case study
Medical devices testing
Requirement
To provide a low cost, flexible tensile test machine which could be used in conjunction with special fixturing, to perform a range of functional and destructive tests on a range of products.
1080
[Page extract]
ASTM D7137 / D7137M-17
ASTM D7137 is a test method that measures the compression residual strength properties of multidirectional polymer matrix composite laminated plates, which have been subjected to quasi-static indentation
1081
Page
Aksesuar kataloğu
Aksesuarlarınızı seçme Doğru test sonuçları elde etmek için numunenizin doğru bir şekilde tutulması ve tutulması önemlidir.
1082
Case study
Car window sliding force tester
Requirement
Bridgestone TG Adelaide, a major supplier of rubber components to the automotive industry in Australia, needed to measure the frictional load associated with sliding a glass window between two rubber guides.
1083
[Page extract]
ASTM F1473-18
ASTM F1473 is a test method determines the resistance of polyethylene materials to slow crack growth. It is also known as PENT (Pennsylvania Notch Test) test.
1084
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
1085
[Page extract]
ASTM D5766 / D5766-M
ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.
1086
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
1087
Case study
Hipodermik iğne keskinliği testi
Özel mühendislik örneği Hipodermik iğneler, tasarımlarının cilde sokma kolaylığını, hasta ağrısını ve cilt travmasını nasıl etkilediğini belirlemek için test edilir.
1088
[Page extract]
ASTM F607-03
The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.
1089
[Page extract]
ISO 34-1
ISO 34-1 measures tear strength test methods for rubber test samples. The test results in measurement of a materials resistance to tearing. Tear strength can also be used to monitor material anisotropy of a material.
1090
Case study
Hijyenik atık kutusu kapatma testi
Özel mühendislik örneği Hijyenik bertaraf tenekesi üreticisi, bir döner emme mekanizmasına sahip bez (bebek bezi) bertaraf ünitesi ile bize geldi.
1091
Case study
Electrical connector insertion and withdrawal forces
Customised engineering example
Push-fit electrical connectors with hole or dimple detents (also known as 'spade terminals') must offer a firm but practical fit.
1092
Event
Wire Crimp & Weld Testing Webinar
The only way of really knowing the strength of a crimped terminal is to pull it.
1093
[Page extract]
ISO 7622-2
ISO 7622-2 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts.
It applies exclusively to conveyor belts with a steel carcass.
1094
[Page extract]
BS 2782-12: 1210A to C
BS 2782-12: Method 1210A to C specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.
1095
Case study
Ayarlanabilir gözlükler
gereklilik Adlens, dünya çapında dağıtılan gözlüklerde kullanılan adaptif lensler üretmektedir. Lensler, gözlük camının yanında bulunan kadranın dönüşünde gücü değiştirir.
1096
Event
VectorPro Software - The ultimate platform for force & materials testing
VectorPro Software: The ultimate platform for force & materials testing
Presenters: Carl Bramley / Moses Da Rocha
1097
[Page extract]
BS EN 12814-1
BS EN 12814-1 is a bend test method for testing welded joints of thermoplastics semi-finished products.
1098
[Page extract]
ISBT PTC-00004
These ISBT (International Society of Beverage Technologists) Sport Closure test methods focus on child safety related parameters such as separation forces and choking hazards of closure components.
1099
[Page extract]
BS EN 1394
BS EN 1394 is a tensile test method to determine the initial circumferential tensile strength of plastic pipes.