Search results
1001
Case study
Hot air balloon cloth tensile strength and tear-resistance testing
Requirement
Ultramagic is the second largest hot air balloon manufacturer in the world.
For obvious safety reasons, the material used must conform to strict standards applicable to the aeronautical industry.
1002
[Page extract]
ASTM D6117-18
ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:
1003
Sensor
Sensors - Universal Testers (ELS)
Sensors
The OmniTest universal testers use Mecmesin's range of high-resolution precision Enhanced Load Sensors (ELS) to record tensile and compressive loads.
ELSA precision loadcell connects directly to an OmniTest or MultiTest-dV stand and communicates…
1004
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
1005
[Page extract]
UL 486A-B
UL 486A-B is a safety standard that outlines the requirements for wire connectors and soldering lugs used with electrical conductors.
1006
[Page extract]
ASTM D3469
These test methods measure the downward forces during the disengagement of lug-style caps from their respective containers. The methods measure the maximum torque developed while the cap is further disengaged by turning of the container.
1007
[Page extract]
ASTM D6068-10
This test method covers the determination of the J-integral versus crack growth resistance (J-R) curves for polymeric materials.
1008
Sensor
Sensörler - Helixa
Tork sensörleri HTC'nin değiştirilebilir tork sensörleri serisi, Helixa test sistemi için özel olarak uyarlanmıştır. 0,1 Nm (0,9 lbf.in) ila 6 Nm (50 lbf.in) kapasitelerinde tüm gereksinimlere uyacak şekilde otomatik kalibrasyon için tak ve çalıştır…
1009
[Page extract]
ASTM D413-98
ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.
1010
[Page extract]
ASTM F904
ASTM F904 is a test method that covers a procedure for comparing the bond strength or ply adhesion of similar laminates made from flexible materials such as cellulose, paper, plastic film, and foil.
1011
[Page extract]
ISO 8113
ISO 8113 specifies a method for determination of the resistance of glass containers to external force in the direction of the vertical axis.
1012
Case study
Headset microphone joint torque
Requirement
Jabra is a subsidiary of GN Netcom and is a global manufacturer of innovative headsets (wireless and corded) and speakerphone solutions.
1013
Case study
Top-load testing PET bottles
Requirement
Esterform Packaging manufacture more than a million PET bottles and preforms per day for major processors of bottled water, juices, soft drinks, dairy and household products.
1014
[Page extract]
ASTM D3950
This specification covers nonmetallic strapping and joining methods for closing, reinforcing, and bundling materials for shipment, unitizing, palletizing, and bracing for car and truck loading.
1015
[Page extract]
BS 7907
BS 7907 gives recommendations for the design and manufacture of children’s clothing to promote mechanical safety. This standard is applicable to clothing intended for children up to 14 years of age.
1016
[Page extract]
ASTM D1708
ASTM D1708 is used to determine the tensile and elongation properties of small plastic microtensile specimens. These plastic specimens can be of any thickness up to 3.2 mm (1/8 in), including thin films. This test method does not require the use of an
1017
Case study
Döner Vakum Soyma Sistemi
gereklilik Aynı boyutta fakat farklı formlarda, bisküvi ve şekerleme içeren bir dizi esnek plastik tepsi için test gerekliydi.
1018
[Page extract]
ISO 8033
ISO 8033 specifies methods for the determination of the adhesion between lining and reinforcement, between cover and reinforcement, between reinforcement layers, between cover and outer lamination (thin layer of material outside the cover for protection
1020
[Page extract]
ASTM D2653
ASTM D2653 determines the tensile properties of elastomeric yarns made from natural rubber, spandex or other elastomers.
1021
[Page extract]
BS 6319-11
BS 6319-11 is a test method for determining creep in compression and in tension for resin and polymer/cement compositions used in construction
1022
Case study
Pharmaceutical sachet burst strength
Customised engineering example
Plastic sachets with welded seams are frequently used for measured applications of liquids, creams and gels.
1023
[Page extract]
BS EN ISO 80369-1
BS EN ISO 80369 “Small-bore connectors for liquids and gases in healthcare applications. Connectors for intravascular or hypodermic applications”.
This standard replaces BS EN ISO 594-1: 1986, BS EN 20594-1:1994, and BS EN 1707:1997.
1024
[Page extract]
ASTM D3807
ASTM D3807 is a test method used to determine the strength properties of adhesives in cleavage peel by tension loading. It allows the comparative testing of cleavage/peel strengths of bonded engineering thermoplastic adherends.
1025
Case study
Toz içecek kabı
Özel mühendislik örneği Uluslararası bir toz sıcak çikolata içeceği tedarikçisi, ambalajlarının çeşitli yönlerini test etmek istedi. Toz plastik kapaklı, folyo sızdırmaz karton tüp kabında paketlenmiştir.