Search results
2026
[Page extract]
BS EN 14477
Packaging, Packaging materials, Flexible materials, Perforating tests, Mechanical testing
2027
[Page extract]
ASTM F1044-05
This test method covers shear testing of continuous calcium phosphate coatings and metallic coatings adhering to dense metal substrates at ambient temperatures.
2028
[Page extract]
BS EN 2597
BS EN 2597 is test method covering tensile testing on carbon fibre reinforced plastics.
Before conducting BS EN 2597, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.
2029
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
2030
[Page extract]
BS EN ISO 205
Adhesives. Wood adhesives for non-structural applications. Determination of tensile shear strength of lap joints.
2031
[Page extract]
BS EN 1895
Adhesives, Adhesion tests, Peeling tests, Paper, Paper products, Board (paper), Disposable, Packaging materials, Flexible materials
2032
Event
Brütsch-Rüegger Tools at INNOTEQ 2025
Our trusted distributor, Brütsch-Rüegger Tools, will be exhibiting at INNOTEQ 2025 - the key event for Switzerland’s manufacturing industry.
2033
[Page extract]
Interpreting compressive strength test results
Interpreting results involves more than noting the peak load. Stress–strain curves reveal additional information such as modulus, yield point, and failure mode.
2034
[Page extract]
BS EN ISO 1806
This standard specifies a method of determining the mesh breaking force of netting for fishing.
2035
[Page extract]
Step-by-step guide to conducting a CMT test
Prepare the specimen - Cut to size with clean edges, ensuring flutes remain undamaged, and condition as per the standard.
Calibrate the equipment - Check the load cell and platen alignment.
2036
[Page extract]
ISO 12048
Specifies a method for testing the resistance to compression of complete, filled transport packages and a method for carrying out a stacking test on complete, filled transport packages using the same apparatus.
2037
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
2038
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
2039
[Page extract]
BS EN 12467
Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio
2040
[Page extract]
Consumer Products
Mecmesin test solutions for products typically found in the home ...
2041
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2042
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
2043
[Page extract]
Speak to a testing expert
If you're looking to validate adhesive joint performance under realistic stress conditions, our applications specialists can help configure the
2044
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
2045
[Page extract]
Challenges and best practices in peel testing
Common challenges
Material variability in thickness, surface treatment, or adhesive application.
Inconsistent specimen preparation.
Operator error from misalignment or incorrect grip tension.
Best pra
2046
[Page extract]
ASTM D3106
This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.
2047
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
2048
[Page extract]
Advances in adhesive testing
Modern systems incorporate high-resolution digital sensors for precise force measurement, real-time data capture with analytical software, and automation to reduce operator influence.
2049
[Page extract]
BS 2782-3: 360C
BS 2782-3: Method 360C specifies a test method for testing the tear resistance of plastics film and sheeting by the initiation method
2050
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.