Search results
751
[Page extract]
FAQs
What is the role of compression texture testing in food quality control?
It delivers objective, repeatable texture measurements to meet sensory and regulatory standards.
752
[Page extract]
Introduction to five-point bend testing
The five-point bend test is a specialised method for assessing the mechanical performance of structural panels, particularly their resistance to planar shear forces.
753
[Page extract]
Understanding corrugated cardboard resistance
The compressive resistance of corrugated cardboard depends on factors such as flute profile, board structure, and paper quality.
754
[Page extract]
Types of torque in packaging
Application torque
Application torque is the force used to secure a closure onto a container during the capping process.
755
[Page extract]
Understanding torque testing
Types of torque testing in packaging
Several torque measurements are relevant to closure performance:
757
[Page extract]
Force systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers?
758
[Page extract]
Introduction to short span compression tests
The short span compression test (SCT) is a mechanical testing method used to measure the compressive strength of materials over a very short span.
759
[Page extract]
Selecting compression testing equipment
Choosing the right testing system is critical for accurate and repeatable results. Factors such as force range, sample type and testing throughput influence equipment selection.
760
Event
Webinar: Adhesion/Peel strength testing
There is a reason people reach for duct tape as a fix for almost everything – adhesion strength.
From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufacturers.
761
[Page extract]
Introduction to climbing drum peel testing
Climbing drum peel testing is a specialised method used to measure the adhesive strength between bonded materials, particularly in flexible-to-rigid substrate combinations such as aluminium skins bonded to honeycomb cores.
762
[Page extract]
How is bulk analysis testing performed?
Compression testing
Compression testing is used to assess how materials respond when compacted.
763
Sensor
Sensors - MultiTest-dV
Force sensors
The MultiTest-dV is a highly flexible tester, which can be configured with either a Touchscreen or Advanced Force Gauge for product testing or an Enhanced Load Sensor for basic materials testing.
AFGA digital force gauge with advanced…
764
[Page extract]
Applications of the peel wheel test
The peel wheel test is relevant to industries where adhesion performance is critical to product function, safety, or durability.
765
[Page extract]
Why is the 90-degree peel test important?
Adhesion is fundamental in industries such as packaging, automotive, constructi
766
[Page extract]
What is the box crush test?
The box crush test (BCT) is a widely used method for measuring the compressive strength of fibreboard packaging, particu
767
[Page extract]
Pharmaceuticals
The pharmaceutical industry is tightly controlled and subject to strict regulations, which means that testing is often at the heart of demonstrating compliance to the various international standards which govern the industry.
768
Accessory
3/8" Upper Chuck Assembly for use on Helixa sensors
432-615
A standard self-centering 3-jaw chuck with key.
It has a maximum ⅜" (9.5 mm) opening and is connected to the Helixa torque sensor via an adaptor with female ⅜" square hole.
Used to secure a variety of test specimens for torque applications of 1.5 - 10…
769
Accessory
Diamond coated jaws for Mec240g U-Form Vice Grip, 5 kN, 30 x 80 mm
Mec240g-BD80
Diamond Jaws (30mm x 80mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
770
Accessory
Crush Test Fixture with Precision Guide
PSV21062
Precise alignment of the upper compression plate with the test piece is essential for optimum accuracy of results. Mecmesin recommends a minimum of self-adjusting compression plates and, for ECT and RCT tests, the Crush Test Fixture featuring a Precision…
771
Accessory
Pyramid (serrated) jaws for Mec83 U-Form Pneumatic Vice Grip, 5 kN, 40 x 60 mm
Mec83-BP
Pyramid Jaws (40mm high x 60mm wide) - nickel-plated having a surface of hardened steel pyramids of 1.2mm tall.
Opening span = 0-10mm, 10-20mm or 20-30mm depending on which rod and piston are fitted to the Mec83 body.
For materials which need a “bite”…
772
Accessory
Upper Key-operated Chuck, square drive, for use with Vortex sensors
432-444
Upper ‘key-operated’ 4-jaw Chuck (small)
Fitted with a square-drive adapter for connection to 'Vortex' torque sensors. Supplied with dedicated chuck-key and 3 different sets of interchangeable jaws. Max.opening 50mm depending on jaws selected.
Used for…
773
Accessory
Rubber jaws for Lightweight Pneumatic Plane Grip, 200 N, 25 x 25 mm
Mec94-BG25
Rubber-faced Jaws (25mm x 25mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = 0 - 18mm.
For fragile samples, which may get weakened by pinching at the contact-edge of the grip. (e.g. thin films, filaments, fibres and…
774
Accessory
Protective Dust Cover for fitting to Vortex-d(V)/-i stand
432-481
The covers offer protection to Mecmesin’s Vortex-d, Vortex-dV and Vortex-i motorised test stands in dusty and dirty environments. They are durable and easy to clean, and feature quick-acting velcro fastening strips for simple fitting and removal.
Dust…
775
Accessory
Bench mounting stand for 'TS' Static Torque Screwdrivers
432-402
Bench mounting stand used for fixing the mid-torque range of 'TS' Static Torque Screwdrivers.
A clearance hole at each end allows the stand to be securely fixed to a bench.
Note: Not suitable for fixing the low-torque range of 'TTH' Mini Torque…