Search results
801
[Page extract]
Key test standards for cone penetration
BS EN 14372 overview
BS EN 14372 is a key European standard for cutlery and feeding utensils intended for children up to three years of age.
802
[Page extract]
How is bulk analysis testing performed?
Compression testing
Compression testing is used to assess how materials respond when compacted.
803
[Page extract]
Abrasion
Abrasion is the surface wear caused by rubbing with another material. The consumer would expect textiles and other products to withstand a certain amount of deterioration.
804
[Page extract]
Why choose Mecmesin for elongation and recovery testing
Precision testing across materials
Mecmesin’s systems deliver accurate, repeatable results for textiles, rubber, elastomer
805
[Page extract]
Why Mecmesin for removal torque testing
Mecmesin offers manual and automated torque testing solutions designed for packaging manufacturers, quality control teams, and compliance officers.
806
[Page extract]
Why choose Mecmesin for flat crush testing
Mecmesin provides precision-engineered flat crush testing solutions designed for accuracy, repeatability, and compliance with ISO, TAPPI, and FEFCO standards.
807
[Page extract]
Mecmesin solutions for five-point bend testing
Mecmesin provides precision testing systems fully compatible with ASTM D2718, offering accurate and repeatable results for planar shear evaluat
808
[Page extract]
Mecmesin equipment for four-point bend testing
Mecmesin supplies a comprehensive range of systems for four-point bend testing, covering both laboratory and industrial requirements.
809
[Page extract]
Why choose Mecmesin for test calculations and automation
Proven expertise in force and torque testing
Mecmesin has decades of experience in precision mechanical testing.
810
[Page extract]
Mecmesin equipment for trapezoidal tear testing
Purpose-built tensile testers
Mecmesin’s OmniTest and Mu
811
[Page extract]
Key standards for breaking torque testing
Breaking torque testing is governed by a range of international and sector-specific standards that define testing protocols, equipment requirements, and performance thresholds.
812
Case study
Inline respiratory filter pull test
Customised engineering example
A manufacturer of filtration products needed to test the extraction force of a respiratory filter when pulled from within an inline medical device.
813
Case study
Syringe tube pull-off testing
Customised engineering example
Pull-off tensile tests require careful gripping of the separating parts in order to avoid distorting them and therefore artificially weakening the joint.
814
Page
Accessory catalogue
Choosing your accessories
To achieve accurate test results it's important that your sample is gripped and held correctly.
815
[Page extract]
ASTM F2255-05
This test method is intended to provide a means for comparison of the adhesive strengths of tissue adhesives intended for use as surgical adhesives or sealants, or both, on soft tissue.
816
Bundle
Catalyst tester for ASTM D4179 and ASTM D6175
OmniTest 2.5
BD002
Catalyst crush strength tester, configured for key international test standards including ASTM D4179 and ASTM D6175.
817
Case study
Synthetic sports surface tuft binding
Customised engineering example
Test method standard BS ISO 4919 applies to the tuft withdrawal force of carpets.
818
Case study
Shoulder prostheses tensile testing
Requirement
Mr Keith Borowsky, an eminent orthopaedic surgeon at the University of Brighton Medical School is developing a new orthopaedic prosthesis for shoulder reconstruction.
819
[Page extract]
ASTM F3014-14
1.1 This test method describes the procedure for penetration testing sharp and blunt needles used for the placement of surgical sutures. It only describes the test procedures (Phase 1) and does not define a test medium at this time.
820
[Page extract]
BS ISO 11040-4
This part of ISO 11040 applies to — tubing-glass barrels (single-chamber design) for injection preparations, and — sterilized subassembled syringes ready for filling.
821
Case study
Fast food tray crush testing
Requirement
As a supplier of fast food trays, the customer needed to make sure that the trays would withstand a certain lateral force without damage to ensure they did not break when being handled and loaded with food.
822
Case study
Card and paper crease line testing
Customised engineering example
A packaging production company needed to test the crease force of the ink-coated card used in their fully-enclosed cartons.
823
[Page extract]
ASTM F2878-10
This test method is used for determining the force required to cause a hypodermic needle to penetrate through protective clothing material.
824
Case study
Removal torque of cap from drug delivery device
Requirement
Global medical technology company Becton Dickinson (BD) needed to assess the torque required to twist off the cap of a drug delivery device.
825
[Page extract]
BS EN ISO 7864
BS EN ISO 7864:2016 specifies requirements for sterile hypodermic needles for single use of designated metric sizes 0,18 mm to 1,2 mm.